Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
hi,
please any one explain me, what is the use of power registers of module such as UART, SPI, ADC,GPIOTE etc..
1.NRF_GPIOTE->POWER
2.NRF_ADC->POWER
3.NRF_UART0-...
Hi guys, now i have done the example as the light control demo description, but i have a question about that how i can let the light server to leave the network? Thank you...
A little background with this question
So, long story short:
To send data using notification, in android, you must first enable CCCD descriptor of matching attribute...
we have made 51822 communication with 24LU1+ successfully, result is 32payload, 2Mbps, 800FPS。
however, after add freeRTOS, our 2.4G will lost 5-8 packets and disconnected...
Hello,
I'm having a lot of trouble debugging some errors on UART. I'm initializing the UART as follows:
void uart_init()
{
ret_code_t err_code;
const app_uart_comm_params_t...
Hello Everyone,
I'm a beginner for nRF52 and my aim is to learn and develop system on nRF52. I have bought nRF52 development board and installed Keil MDK on my system....
I have to talk to a SPI device, which gets an address and then needs some time to handle the address. Afterwards the transfer can continue.
Is this scenario possible to...
timpwmadc.c
It is perfect (wonderfull!) idea to use programmable system PPI (EEP->TEP+FORK) alternative
PGA.
But I get some problems:
I tried to program a TIM3 to...
Hi,
Is it possible to call an arbitrary function at a breakpoint in gdb on the nRF52? I know you can with normal gdb, but I haven't been able to make it work with the cross...
Hi
I have a project to model the RSSI based indoor location using Bluetooth beacons. However, in order to do the basic distance and RSSI relation, I want to sense the channel...
Hi, im using nRF 52 DK. I interfaced mpu 6050 by using the example found here (BLE example found here is not working properly, dosent connect with uart app). I'm particularly...
Hi,
Does the erase target in the makefile completely erase the flash? I'm having strange errors when trying to read the flash (i.e. I can't read anything from flash, even...
Hi, Schematic and Code As shown above, VCC 3V (DEC2 and VCC open) current is only 3.8uA, but VCC 1.8V (DEC2 and VCC short circuit) current exceeds 1mA, what am I mistaken...
