I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
We are seeing issues with Segger Systemview Post Mortem Mode. Original issues were revealed on our custom board with SDK 2.6.1. After enabling the feature firmware crashes...
Hello,
I would like to test TX for ltem. I'm using nrf9160. I would like to use: - Band: 1 - Frequency: 1950 MHz - Tx power: 23 dBm - Bandwidth: 5 MHz - Modulation: QPSK...
Hello,
I've recently was checking out the Zigbee Weather Station application running on the Thingy53 and have spotted a weirdly formatted log message regarding temperature...
Hello everyone, recently I received a thingy:91x with an extra truphone sim card.
I am based in Indonesia and want to test the cellular connection from device but doesn...
I built the demo zephyr/samples/bluetooth/hci_usb for my nrf52820, and it worked well.
But when I tried to read its manufacturer name by using command `hciconfig -a`, it...
Hi there,
I want to capture all the logs made by Zephyr and printk() calls. I want to forward these logs via USB using our custom application protocol for debugging purposes...
Hello folks,
I need some help troubleshooting a BLE antenna issue on our custom nRF52840 PCB . Any insights would be greatly appreciated!
Issue:
BLE sometimes advertises...
ncs v2.9.0
nRF52832 DK (NUS central)
nRF52840 DK (NUS peripheral)
1) When connected, see the empty PDU from peripheral to central about 100ms interval.
2) To use...
I'm trying to add an Aquara temperatur sensor to Zigbee shell running as coordinator on a 58233DK.
Regarding the logs in the serial terminal, it looks like the network was...
Hi,
I am using a nRF9161-dk with the nRF7002-ek shield WiFi tracking.
Using the nRF Connect Quick-Start, I downloaded the nRF Cloud Multi-service application and went...
I'm new to Nordic technologies and ML MCUs!
Does the ARM Cortex-M33 core, nRF5340 audio DK devkit, without any other board od periferic, support edge impulse ML? If so...
NCS 2.7.0 nrf52840
I noticed in i2c_nrfx_twim.c there are some calls to pm_device_runtime_get, while in another thread ( thread ) it was mentioned that Nordic is no longer...
NCS 2.9.0
nRF52840-DK
Using the OpenThread CLI example.
After turning on the TCAT function, when using MeshCoP Commissioning, the joiner will experience a system failure...
Hi, we have a NPM1300 chip connected as I2C slave to a nrf5340, acting as I2C master. Everything works fine, but there is a small detail in the NPM user manual that I would...
