Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I have a vendor specific characteristic for the battery voltage in my device, expressed as an actual voltage rather than a percentage. Values are 0.000V to about 4.300V and...
HI,all!
I recently using pstorage to store data
and the pstorage_store(); funtion always returns NRF_SUCCESS, but never triggle the cb_handler, is that normal?
by...
[environment: s110_nRF51822_7.0.0 + SDK nrf51_sdk_v6_0_0_43681 + PCA10000(QF AAG0)]
I failed to get pstorage working in my own code, then I picked up the sample code from...
My NRF51822 die. When connected, keil can't download or erase flash. But it can be found by SW port when I just power on, then it almost be unavailable at the same time. ...
Hi,
I am trying to use the RX interrupt on the PCA10001 board, using UART0 for wired communication and S110 (s110_nrf51822_5.2.1) for Bluetooth LE communication at the...
Hi, i'm trying to communicate between a msp-430f5529 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
Hi there,
I'm currently facing the problem, that an example as simple as
volatile float sum;
extern "C" int _start()
{
float a = 1.0;
double d = 2.2;
sum = a ...
I have a nRF51822 mkit board which I would like to use as a BLE peripheral to connect to my linux computer with BlueZ. I would like to be able to have a simple GATT connection...
Hi,
I'm trying to get a SPI based peripheral going without much luck.
One thing I noticed, in the debugger, is that on my implementation the field spi_base_address->POWER...
Hi,
I'm getting problems on the pca10001 uart example. I get the "Start:" string on the terminal but it can't echo what I type on the keyboard. Another thing is that I...
The nrf51 powerdown examples
github.com/.../nrf51-powerdown-examples.git
Are these power down examples are helpful. They clearly indicate how to power on the nrf51822...
I have a custom board using the nRF51822 as a peripheral with the S110 SoftDevice. The centrals are mobile apps, both Android and iOS. The device spends a lot of time in a...
Hi
I'm trying to run uart example on nrf6310.
I followed following link.
devzone.nordicsemi.com/.../
and I defined ENABLE_LOOPBACK_TEST.
it was resulted in blinking...
I am using sd 7.0.0, I have a simple bootloader implementation that follows the bootloader sample code pretty closely. When I jump to my application from the bootloader and...
