I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
Hi There,
Are the GPIO levels high impedance when the system is in off mode? Can you give information about their status? For example, one pin of the device is configured...
Hi there,
I'm on Ubuntu 22.04.2, 6.5.0-41-generic kernel.
I've been trying to setup the nRF connect toolchains & SDK through VSCode. Things seem to install fine, but when...
Hi,
I have a solution that every 15 minutes needs to perform a WiFi Scan and save the BSSIDs that it finds. Sometimes it will find the maximum number set and will complete...
I am getting an error message when trying to use a nRF5340 DK with a Waveshare 1.69inch Touch LCD Module on the Zephyr sample code with minimal modifications. When I flash...
I'm using custom board of nrf5340 with nrf7002.
Use helloworld sample and have set "config serial=n" and "config device pm =y".
The current is 90 ma when I don't do anything...
Hi,
I have new requirements for nRF52832 using the NRF Connect SDK to develop firmware. I want to know how it supports audio playing with the I2S MAX98357. Is there a possibility...
I am working on a pdm microphone using nrfx pdm driver (INMP621) When I am saving the pcm data into .pcm file using sd card and playing the .pcm file in Audacity I am getting...
I'm using nRF52840 with nRF5_SDK_17.1.0_ddde560, using the ble_app_multirole_lesc example file.
When I set extended = 1 in scan_init , the debug session jumps to NRF_BREAKPOINT_COND...
Hi All,
I flashed an nRF5340 DK board with a samples/bluetooth/hci_uart image and one more nRF5340 Audio DK with a samples/bluetooth/peripheral image.
I have not made...
Hi, I am making BLE low power pult, using nrf52811 chip and NRF Connect SDK v2.3.0.
So, the device is sleeping and waiting for button event
When button is pressed, device...
Hi Sir.
customer want to add FEM for nRF7002, target to extend range around 1.5KM.
please check if nRF7002 can support FEM for this application.
Thanks.
Hello,
I'm new to Nordic and I'm currently learning rust on an nRF7002 DK. I know that the LED0 of the nRF7002 connects to the GPIO1.06 of the nRF5340. However, when importing...
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. I want to send a packet with a notification to my smartphone and then disconnect immediately....