hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello Nordic Experts,
Recently, I am using the nRF52840 dongle to sniff the Scannable Directed event, but I found that the AUX_SCAN_REQ cannot be sniffed, but the SCAN_REQ...
I'm using the UDP sample from SDK 1.8.0 with the following modifications:
No PSM
No eDRX
Send 100 bytes every 15 seconds
This is on the nrf9160-DK board.
I suspect...
I'm using embedded rust for a project on the 9160. If i configure any of the AIN0-AIN7 pins with the SAADC, my sleep current is 850 uA. Default config is resistor bypass,...
Hi,
I want to use NRF_RADIO->SHORTS register in my standard BLE application.
I am using nRF5 SDK15.
When I write in to this register before enabling the Softdevic, it...
hi,We developed a Bluetooth product based on NRF52832, but the bandwidth test was not qualified. According to the requirements of FCC Part 15.247 regulations, the Bluetooth...
Hello,
I have a project that is based on the peripheral_uart example that receives start and stop commands from a periperal_central device via BLE to send ADC samples...
Based on the NRF52840DK, we want to do a USB CDC DFU upgrade function, but we don't want to use the BLE demo. You want to enter the duf mode by adding and modifying registers...
I am facing a problem. Two sensors are triggering with data_ready pins and a timer value is captured upon the event. But the value can be stored only in RAM if a context switch...
HI,
I am working on nrf52833 board, while working with flash in dts file i could see that write_block_size is 4 bytes. Is there any way to reduce that , i need it as 1 byte...
Hello guys.
I am using a board based on the NRF52840 device. We run a code that we developed earlier and it was not well coded but working. it involves the interfacing of...
I am using Nordic Uart Service (NUS) to transmit raw data from nRF52832 device to iPhone. But it takes longer time than I except. Can I add debug message to make sure CRC...
Describe the bug When running the example project sample/bluetooth/periodic_sync on a nRF52833DK and sample/bluetooth/periodic_adv on a custom nRF52833 board, the central...
Hello ,
I want to convert the code of dfu pca10056_usb to pca10040 for this i have updated the following -
1. Updated board from PCA10056 to PCA10046
2.Updated the...
Hello
I worked this example with nRF52840-DK kit it works very well. But, when i use thingy:53 with nRF5340-DK, I am not getting any ouput in puTTY screen. Even any example...
