Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I am trying to use the experimental task manager of the nrf52sdk, version 17.1.0. I've come across what I would call a bug, but there might be a reasoning behind it, so that...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle.When...
Hello everybody.
I am developing a BLE application in which I am using WDT every 12 seconds and a RTC interrupt every 10 seconds to send some information.
When you press...
Hi,
We are using nRF5340 and we are migrating to v2.0.2 NCS sdk from v1.9.1.
In our design, the SPI MISO pin is P0.10. From the dev zone tickets, I found that this P0...
Hi,
I'm trying to send I2S data (~ 16 kHz, 24 bits) via BLE using the nRF52 DK and the nRF5 SDK 17.1.0. After I get the data from the I2S driver (by specification, they...
Hi!
To measure the voltage level of a coin cell CR2450 can be done in different ways.
You can use the comparator, the low power comparator or the ADC.
I wonder which...
Hi, The getaddrinfo() function returns the same IP address for www2.domain.com and domain.com, namely that of domain.com while they are running on different servers and have...
Hi
I am currently working on a Matter project.
I configured OTBR with Raspberry Pi, completed pairing with nRF52840 board (Light bulb), and confirmed that Light on/off...
Hi,
In order to make firmware updates over Bluetooth work, I need to enable the MCU boot loader. Is use CONFIG_BOOTLOADER_MCUBOOT=y in my prj.conf file to enable it. My...
I'm doing with the nRF Connect SDK v.19.1, testing the project C:\ncs\v1.9.1\zephyr\samples\hello_world.
The main. c file is
void main(void) { printk("Hello World! %s...
Hi， i'm use latest ncs develop bluetooth extend advertising, and i'm try use west build -t menuconfig to config scan filter config
such as BT_CTLR_DUP_FILTER_LEN or BT_CTLR_DUP_FILTER_ADV_SET_MAX...
I want to define config values in an optional overlay that is enabled after writing to a custom service/characteristic using NCS. Based on this https://devzone.nordicsemi...
Hi,
in my company, we are using an nRF9160 on a custom board. Recently we updated from NCS 1.8.0 to 2.0.2 (we also still use spm for now).
1.8.0 was already not super...
Hello all, Ive combed through the NRF52840 datasheet and the BMD341 datasheet, and SDK examples attempting to determine if through software (and possible hardware change)...
