I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
How Can I store information about button port ? I have two buttons P1.02 and P0.02. I have
And I have one function to init button
the most interesting is callback...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Segger Embedded Studio 4.16
I am working...
I'm trying to run LTE/BLE Gateway sample on nRF9160DK , i followed all the instruction in the sample instructions.
The Jlink RTT for nRF52840 and LTE-Link Monitor logs are...
Hi nice people, I am working on developing using visual studio and Make environment. I am trying to function UART tx/rx interrupt works but no luck. The TX and RX works perfect...
Hello, I've been trying to launch zephyr SPI example, but I'm having issues with SPI sending anything. The code itself does not throw any errors, and it seems like my board...
hello sir ,
i am using thigy91 board and uploaded the asset tracker application code from ncs sample code . ii am getting humidity data on my azure cloud .but there was...
Hello everyone!
We are using nRF51822 SoC together with s130 Softdevice. nRF5 SDK v12.3.0 is used for firmware development together with the Segger Embedded Studio.
Among...
Hardware: nrf9160DK Modem FW: v1.3.1 We have been evaluating and configuring our proprietary application for NB-IoT, which is initially designed for LTE-M (CAT-M1). The Application...
Hello,
I'm using a central device that lists all nearby peripheral devices by their MAC addresses like so:
but I also want to list the names of the devices as they...
Hi Nordic,
We are preparing to validate a product that contains the UBlox BMD-340 with the Nordic Softdevice. We would like to use the Nordic Semiconductor “nRF Connect...
Hello!
I have used most of the GPIO pins on the nRF52DK, and most of them work. But I cannot get pin 21 to behave. I want to use it as an input. I have configured it as...
In nRF_SDK_For_Thread_and_Zigbee, on the nordic BSP package following three-button functionalities are available:
#define BSP_BUTTON_ACTION_PUSH (APP_BUTTON_PUSH) /**< Represents...
Hi,
I have 2 boards, one with monogoto esim and one with ibasis esim when I try with monogoto everything is working fine
when I try with ibasis esim i can't get registered...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
