Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I was able to write some I2C code to successfully work with the TCS34725 by porting a library from Arduino without fully understanding what was going on. Now I have to port...
Hello,
I am using th PCA10040 board, and I can build my project without problems. But when I debug it, 'stopped by vector catch' error appears. I have been reading possible...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i have an issue with not responding pin interrupt so i try to run zephyr example to see how...
nRF9160 DK NCS v1.6.0, SLM with:
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
Sometimes after at#xsleep=0 and several pulses on pin 24 SLM wakeups with...
Hi. I'm testing the multi-image DFU in nRF Connect SDK 1.7.0. I'm seeing an issue with the firmware images not getting reverted when it should.
Here's what I'm doing:
...
Hello!
I am having unexpected issues in setting TX power using Softdevice call to SD_BLE_GAP_TX_POWER_SET via sd_ble_gap_tx_power_set. Please see the code below.
The...
I am developing with 52840.
We checked button-related problems while using the source that checked the behavior on the DK board on the adafruit-circuit-playground-bluefruit...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i have an issue with not responding pin interrupt on an input pin
this is my trigger pin...
The following code works perfectly fine every single time if i use NCS 1.5.1..we decided to move to 1.6.1 recently, and while we were able to get everything else working,...
Hello I'm making a custom usb device class with 1 IN & OUT Bulk endpoints running on a nrf52840 with 340. The device reads the data correctly that are being sent by the host...
Just no clue on including the proper files, initialization and how to use API in main or handler. My intent is once a led is on trigged by a button pressed up from the other...
I am trying to develop a peripheral targeted for mobile devices that can either behave as a touchscreen (several simultaneous contact points, useful for performing gestures...
Hello
I wanted to use the MQTT simple example (which works great) and add timer, so that MQTT will be send every 20 seconds:
on main I added:
struct k_timer my_timer;...
Good day!
This function in scheduler server compares timestamps only between each other and if scheduler stores settings after reset and set new time (without bt_mesh_scheduler_srv_time_update...
