Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I was using the AWS-IOT example and all was working until it wasnt. In troubleshooting this, I loaded the modem shell example, to see if it was a network/connection...
Hi everyone,
I implemented nrf5_SDK_17.0.2 ble_app_uart example, so I connected an external device to my nRF52840 DK and I received the data by my android phone.
Now I...
Hi,
I'm using the nRF52840-DK with SDK 17.0.2. I've developed part of my app, and would like to integrate secure OTA reflash for it. I've copied the code at examples/dfu...
Hello,
I am wondering if there is support for secure web sockets (wss:// protocol) together with the NRF52840 and if there are any example available. So far I got communication...
Hello Devzone Community,
To compile nRF Zephyr based applications at the command line normally depends on the meta-tool `west`. `West` has many capabilities and options...
Hey all Trying to understand how to properly build a basic bluetooth example without errors using zephyr between the 2 cores Error: manually cleaning and flashing reading...
Hello,
I use this code for system_off on a nrf52840 custom board. const struct device *button = device_get_binding("GPIO_0"); gpio_pin_interrupt_configure(button, SW0_GPIO_PIN...
nRF52840 Dongle is configured as Sniffer in the right way according to documentation. When sniffing capture on Wireshark is started, only the Advertising packets are captured...
I have a project where I use the nrf9160dk as a gateway between a BLE sensor and LTE.
The hci_lpuart sample is flashed tonrf9160dk_nrf52840 and the nrf9160dk_nrf9160_ns...
I got a Segger J-Link EDU to be use to program my Nordic Thingy 91. I have previously program the device via USB using the NRF Connect Desktop :Programmer. But connecting...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). I am using ncs v1.7.0 for development. I am trying out a few things...
Hello guys,
I would like to work using nRF52 as my processor to create products in the future, but I heard about Specific Absorption Rate (SAR) testing and that is good...
Hi all, I am a little confused by the requirements for the external GPS antennal options. My board is version 1.0.1.
In this page ( https://devzone.nordicsemi.com/nordic...
