I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I've modified an example project.
How do I go about exporting it, so that I can share it with other devs and they can then flash the same program onto their Development...
hello,
i am working on nrf52 dk board .NUS sdk 16
I'd like to know the start/end characteristic handle values for each service. Is the 32-bit service handle encoded as...
I have inserted the groups cluster at an endpoint. Yet, and eventhough a group seems to be additioned to the device (the device responds with 0 to the add group command from...
hi:
I need help with a problem.
Error in merge file for 52810.
use sdk:nRF5_SDK_17.0.2_d674dde
bootloader:secure_bootloader
app:ble_app_buttonless_dfu
app:FLASH_START...
Dear Nodic friends,
We use nrf52833 to design a BLE control box with USB DFU function.
During USB DFU, DFU Trigger Library will reset nrf52833, so we should connect a...
Hi
I'm trying the light lightness example, I'm using nRF Mesh Android app for provisioning. I've 2 nrf52840 DK's. One is for client and other one for server. Both of them...
Hi,
I am trying to implement BLE on nRF52840 using Zephyr APIs. I am wondering if anyone can elaborate how to use bt_gatt_write() and bt_gatt_read(). As of now, I am able...
Hi:
s132_nrf52_7.2.0_release-notes.pdf shows us below words in page 3 about limitation:
GATT:To conform to the Bluetooth Core Specification v 5.2, there shall be no secondary...
I am creating a system with one BLE central device (nRF52840 DK) and many peripherals (nRF52840 Dongles). I am attempting to create a BLE central device that interfaces with...
Hello i have a working program with ble:uart and twi in a nrf51822 device with sdk 12.3 and softdevice My system works perfectly when i use other gpio as scl and sda (external...
When I'm tuning the RF output (front end) of the nRF52832 to match 50 Ohm what state should the chip be in? Unprogrammed with power on or off? Or in receive mode with power...
Should a firmware written for nRF 52832 run smoothly on a nRF52833 if no changes in functionality are desired?
If changes to the firmware are needed, which layers must be...
Hello , Vivek here. I am planning to use NRF52832 in my design and interface it with a microcontroller. And i am new to handling bluetooth protocol. When I was going through...
Hi,
i am using nRF52840 SoC and Had confusion on pin mapping for SPI (external flash) and I2C (external sensors) as below:
I found one similar query and it was said...
Hi,
I would like to write a code where I send a packet from a nRF5340 DK to another nRF5340 DK by using Zigbee.
I would like to also be able to use printk and see the...
