I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I need a gpio to control an external peripheral.
I thought to code should be similar to controlling one of the leds.
board overlay:
&gpio17 { status = "okay" gpio17...
Hello ! When I run the direct test mode example found in "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8" in transmission mode, does it only transmit packages on a channel...
Hi,
What is the correct way to write to UICR at runtime?
I am using the code below but the MCU crashes on the first line with no call stack trace.
NRF_NVMC->CONFIG ...
Hi,
I'm trying to collect data for average latency for nRF52840 using an Android Smartphone as Central and nRF as peripheral.
Latency is being measured by the Android...
Hello,
I want to send data via Bluetooth Serial as well as USB CDC Serial and currently, I am getting data rates up to 3.2KB/s on a Windows Laptop. I read this https://devzone...
Hi Community,
Facing the RF functionality issue on nRF52833 on our custom board.
Our board is functioning well with nRF52840, then it failed after migration to nRF52833...
Hello,
I am searching for nRF52 Flash memory mapping. I got some memory map from info-center but for me, it's not working.
The application Starting address is wrong in...
I couldn't launch FOTA upgrade over Bluetooth for nRF5340 PDK. I followed this guide developer.nordicsemi.com/.../ug_nrf5340.html to fulfil FOTA upgrade for nRF5340 PDK. I...
Hello,
My BLE peripheral device based on BLE uart example with nrf52832 has an issue.
My device is paired with central device and I turned off the central. My device started...
Any one tested with Strontium micro HCSD card?
I followed the the suggestions like BUFFERS=8 AND config_gpio=y.
I am getting the error Storage init ERROR!
GPIO Pins...
I am merging interactive command and buttonless dfu base on https://www.u-blox.com/sites/default/files/Add-NordicSemiconductorDFU-to-SDKexample_AppNote_UBX-19050198.pdf
...
I just recently got both nRF51422 and nRF52844 DK. However, when I tried to connect through J-LINK, the error message popped up: No emulators connected via USB. Do you want...
Hello,
I built a network of 3 parts. Each has a PCA10059 nRF52840 dongle.
Raspberry Pi 3B+ Border Router using the image from 4.1 SDK. This has the NCP
2X Full Thread...
