I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I have a customer requesting any version above 0.8.5 for part number nRF9160-DK.
Can you tell me what date codes would have the requested versions?
thanks,
Russ
QB79869...
I'm looking for a low energy communication method for a wireless PIR motion sensing device. The system will be battery powered so RX current draw is particularly important...
We are revising a design using the NRF9E5, we are experiencing problems with the third harmonic when configured for 915MHz band, the higher we go up the band the worse the...
I am looking to build a custom board using nrf52840 and want both UART and flashing capabilty on the custom board. I have a NRF52840dk that I will use to program the custom...
I want to increase the pull-up resistor value to educe the current consumption.
but, I am afraid that the GPIO input will not be recognized as High.
I want to know the...
Hi,
I can't find this information anywhere in the AT command manual or datasheet. What is the accuracy for " AT%XTEMP?" and "AT%XRFTEST=10,1,0"?
Kind regards,
Thoma...
Hello,
I'm trying to generate project to realise new user-cases with wireless mesh networks.
I did a demo with the Thingy52 at flower greenhouses
They are very interested...
HI! I've done the basic Blinky and UART examples, and now have to move on to programming something on my own. ( I have to send EEG signals from one BLE board to another/notebook...
hai ,
i tried nrf52840 ota over BLE from third party (ESP32).
As per the DFU protocol implemented logics and upto init packet (.dat file) getting expected response from...
Hi, I'm looking to use P15 (Shield Debug out connector) on nRF9160-DK. Description here https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk%2FUG%2Fnrf91_DK%2Fhw_debug_out...
Hi I used the light ctl/lc example project and connected to it with my iphone app which uses nordic sdk. I made a slider which sends messages quite often to the mesh device...
We are presently using Raspberry Pi 3 Model B to observe BLE packets coming from sensors that have NRF52.
We are also able to do DFU OTA using the Nordic NRF52840 USB dongle...
Hi,
I am working on a design of very low power sensor, based on nRF52833. Most of the time my device spends advertising only, with sensor data transmitted within advertising...
Hi,
i want to devolep a keyboard by nrf52840,now the problem is some funcation the usb examle have not,so i want to konw how can i add the
1.consumer control？
2.system...
Full error report:
<info> app: Connected <error> peer_manager_sm: Could not perform security procedure. smd_params_reply() or smd_link_secure() returned NRF_ERROR_INVALID_ADDR...
