I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello,
nRF52811, SDK16.0, Softdevice7.0.1
We had developed our application based on nRF Blinky Android sample app for nRF52840. Now we want to port same app for nRF52811...
Hi,
I would like to ask if it is possible to use both Radio and NVMC at the same time (no SoftDevice)?
My scenario:
Start Radio and configure RX mode.
Write/erase...
Hello
I use nrf52840, Keil uvision 5.26, Win10.....
when i test the board, program run into hardware fault.
that reason is No I2C response, and i delete int the I2C...
I am developing a device which will have Nordic's UART service and it also need to be able to bond with the central. I am using SDK 12.0.0 and VisualGDB for my previous projects...
I'm working on getting an eclipse project working for my nRF52840 application that is currently working with a Makefile. My issue is that once I reset the board, or power...
Hi below is the function i am using to run garbage collection after deleting the data but the result i am getting was the same as before garbage collection.
I mean DIRTY_RECORDS_BEFORE_GC...
I have the following questions about PM and what it generates. My relevant board and config files are below, along with the PM partitions output.
1. Can you explain the...
I am using SDK v17 and Segger v4.52 but for some reason none of the print statements are being printed in the debug terminal. I think I had to enable these two things in sdk_config...
I am sending or trying to write character to ble_app_template but its giving error and its not receiving character.
this what i am trying to send-
if(strcmp((const char...
I see an ID that queries or prints RSRP/RSRQ/Cell ID-related information, but I don't see the AT instruction sq.E. for SINR, where can I print SINR information?
Hello guys,
Just received the Thingy91 and trying to upgrade the model firmware to v1.2 but it fails like this:
However I successfully been able to flash the modem firmware...
Hi Team,
We are using the nrf52840 soc for our application along with crypto engine (mbed TLS ) along with RNG, ECC, SHA256.
While validating the digital signature with...
Hi,
Do you have any direction finding evaluation kits for now? Although I saw many similar questions and until four months ago the answer is still NO, but I still want to...
we'r developing our product based on nRF51822 and also using BLE(Bluetooth) as wireless device.So, we want to release our first product in this year in markets. The next steps...
Hi Forum, 1.) The APP_ADV_... parameters in ble_advertising (SDK 16.0) are taken only from _fast_ , is this intended?
2.) s113 allows only TX_POWER of 4dbm, although the...
