Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello,
Our team is new on development nRF52832 firmware.
Now we have an issue on standby current for nRF52832.
We have a 5 second timer for a PWM output.
Sleep (System...
Hello there,
I am facing some difficulties while using nRF52832 NFC for an application.
When I tap the nrf52832 device on the NFC reader the nrf52 cannot able to respond...
Hi, we are currently looking at making a zigbee light switch using the 52811. However since the zboss library files are compiled with FPU directives the only way to build...
I need to read data from sensor and publish it to the mesh network. So the question is do I need to create Sensor model for that or, as in one of your replies , you suggested...
Hello Nordic Team,
I want to connect peripheral using Mac address, i am setting mac address filter in Scan init but Filter is not getting set
below is my Scan init function...
Hi there,
We have a network of zigbee with XBee-PRO modules working as co-coordinators and end nodes. I have to use BMD340 zigbee node to join that network as well. We have...
Do you have any example which is using NRF_SDH_DISPATCH_MODEL_POLLING for advertising, as well as scanning.
In nrf_sdh.c file, there is only interrupt mechanism in example...
I have an nrf52840 dongle. I can enter into DFU mode and the nRF programmer application recognizes it and shows the memory layout.
When I copy sniffer_pca10056_129d2b3...
Hi,
I am using nrf52832 for advertising and scanning. My board stops advertising after disconnecting.
I am calling all initializations (like ble_stach_init() ) from my...
Hello Sir is it possible to test Zigbee Coordinator project with one nrf 52840 board and one Hue bulb
Example from light control example ->light-coordinator
Hi Support,
This issue happens in nRF5_SDK_16.0.0_98a08e2 and nRF5_SDK_15.3.0_59ac345.
Directly import the example from SDK (examples\peripheral\flash_fds) into SES, build...
Hi,
I'm trying to get NRF Connect 3.3.0 connected to a nRF52 DK with a PCA10040 and get the following when I try to connect to the device: Received status with code 0 PKT_SEND_MAX_RETRIES_REACHED...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
I'm having some issues with the example provided in $MESH_SDK/examples...
Hello everyone,
I just started working with 802.15.4 using nRF52840. I wanted to know weather we can do RX-to-TX using 802.15.4. If yes what are the API's available to do...
We have problems with the restart which the application does after receiving the DFU attribute is written.
Startup should work like this as I understand it: the reset vector...
