Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Dear All,
I am trying to use sscanf in a project and I am getting the message that it is undefined. I am including <stdio.h>.
I cannot understand/find the reason of...
Hello everyone,
I'm taking the "Bluetooth Low Energy Fundamentals" course For all the examples I followed in the training, from what I understood, we loaded the peripheral...
Hello, we are trying to use the shell over bluetooth but in default it also uses the uart contorroler of the board. us there any configuration option to disable the zephyr...
I have not messed around with devicetree much before this point. I'm trying to create a custom dts and bindings for my device. Within my custom dts file, I reference the nRF52833...
I am working with nRF52840 with MAX86141 and learning how to setup the SPI connection
Here is an opensource example : https://github.com/JON95Git/zephyr-spi-directly
And...
Hi Support Team,
I am using the nRF7002DK board for our product POC (Proof of Concept) purposes. We plan to use the same MCU, the nRF5340, for our final product.
I have...
Hello,
I am using an nRF9160dk with the nRF52840 acting as the BT controller running the Bluetooth: HCI low power UART sample ( https://developer.nordicsemi.com/nRF_Connect_SDK...
modem_info_get_current_band expects an uint8 pointer to store the band into, but scans for an unsigned int (probably above 8 bit) in nrf_modem_at_scanf. This leads to memory...
Hello
I am working on a WiFi application using a custom board equipped with both the nRF5340 aswell as the nRF7002. When requesting a WiFi connection using the net_mgmt...
I'm using 2 nRF52840 DK to run a data transfer test between a central and a peripheral.
The Central device uses ble_app_uart_c, The peripheral uses ble_app_uart. These examples...
We are trying to re-layout the PCA10059 Dongle. I would like to continue to use the existing USB bootloader .hex file for updates via CDC_ACM. One thing I am confused about...
Hello, DECT NR+ seems as a good fit for our product, however, current stack providers(Wirepass and Lynq) are not suitable for us. I'm wondering are there other companies who...
Hi i am currently using nrf52840 s140 sdk ver 17.1.10 using central uart and i need to add dfu ota code to it how can i add what is the required files to it we tried these...
Since the tickets are scattered, I will summarize the questions about nRF5340 Audio again.
Prerequisites
NCS version is 2.5.0. Raytac's MDBT53-1M is implemented on a homemade...