Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello
I am using nRf52805 based BLE peripheral using the Nordic UART Service (NUS). The device transmits numeric data periodically using GATT notifications (NUS TX), and...
Hi,
We have products in the field using SDK 15.2 with its associated S140 SoftDevice s140_nrf52_6.1.0_softdevice, and bootloader.
We are upgrading our application to SDK...
I've succesfully setup multiple nRF7002DK boards with an example app to connect to WiFi.
One out of the five boards the Wifi does not work. The interface stays down in Zephyr...
Hello community
I have tested the v3.2.1\zephyr\samples\boards\nordic\system_off example and it works fine on my nrf54l15dk. Now i wanted to use parts of it for my custom...
Currently I learn the current DFU example from nrf_sdk but I failed in the last step:
I compiled the bootloader example secure_bootloader\pca10056_uart
in the...
Hello, when sending audio packets using a broadcast stream one can provide the seq_num of the packet (using the function `int bt_bap_stream_send(struct bt_bap_stream *stream...
Symptoms:
When running Bootloader + SoftDevice + App (with SoftDevice enabled in the app), The bootloader runs correctly and starts SD. The app is started, but crashes...
Hi,
I'm using nrf Connect SDK 3.1.0 and want to control three WS2812B LEDs with the LED strip driver. Therefore, I created the devicetree entry similar to the sample:
...
Hi!
We are currently building a product using nRF9161 on (rather old) nrf-sdk version v2.9.2.
After production we are testing the hardware functions of this product using...
We have a product that was built on NRF SDK 1.6.1, which is zephyr 2.6 as far as I can tell. We have ported it to zephyr SDK 3.7 (not NRF SDK) because there have been many...
I struggle with my experimental project of breath and apnea detection. It works except that I cannot reduce the poser consumption bellow 1mA when powered on battery, despite...
Hi I saw NRF Connect for Desktop is in the maintenance state, no more development. New recommendation is NRF Connect for VS Code, right? In this case, how about the PPK2 tools...
Hi,
Currently, I know that OTA updates for the nRF5340 can be performed using Device Manager and the nRF Connect mobile application. However, if using a PC, is it possible...
SoC: nRF52832 or nRF54L15 SDK: nRF Connect SDK v3.2.0
We are considering controlling coexistence via PTA signals when operating a third-party Wi-Fi device together with...
