Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi there,
We're using nRF52840, IAR 8.40.1, nRF5_SDK_16.0.0_98a08e2. My question is, I need to toggle a GPIO pin right after SPI finishes the TX transaction and right before...
I am trying to use both USB and BLE on an NRF52840 using SDK 15. It hit a hard fault during initialization, specifically when it tries to enable the USBD IRQ.
It looks like...
I am familiar with the PTCRB certification process for an IoT device incorporating a certified module. https://www.ptcrb.com/wp-content/uploads/2020/08/10_Steps_to_PTCRB_Cert_for_Cell_Enabled_IoT_Devices...
Hi, all
How to enable and set fast advertising and slow advertising in NCS.
We always set advertising parameters in legacy SDK like below, how to implement it when using...
Hello All,
Thank you for reading my post. I have finished developing a small battery powered device I have been working on and just completed programming the functionality...
Hardware: nRF52840dk
SDK: NCS v2.0.0
application:
Calling bt_encrypt_be() during OpenThread network traffic hangs the device when using MPSL with OpenThread 1.2. ...
Hello everyone,
I'd like to build a Relay Node in Light Switch Example but I don't know how to implement firmware.
Can you support this for me? Thank you so much.
...
Hello,
I need to build a project in a Docker container. It built fine under Windows 10 with a connect SDK v1.9.1.
Now I am using a Docker image built with the Dockerfile...
Hi,
I am trying to update nRF5340 netcore application, but i don't know how to start.
Here is what i tried:
1. I created two custom applications for nRF5340 appcore...
Hello DevZone,
I want to transmit some connection information such as a Bluetooth address serially to my peripheral and have it add it to its whitelist.
I have read a...
Hello,
I'm am trying to use the UART0 bus on the network core at the address:
uart0: uart @ 41013000 {
compatible = "nordic,nrf-uarte" ;
reg = < 0x41013000 0x1000...
Hi,
ubuntu 20.3
vscode + nrf connect
when i creat project from sample code unicast_audio_client, i get the following compiling error message:
* Executing task: nRF...
Hey!
I have inherited a project with a nRF9160 + nRF52480 combination to do LTE and BLE communication.
The setup is as follows:
- nRF9160 using BSDlib @ NCS 1.5.0...
My Peripheral device (nrf Connect SDK, nrf52840) will pair using NFC with an Android (8.0.0) phone. But although the Nordic device shows it is connected (in its UART output...
