Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
1， The SDK is nRF5_SDK_14.2.0_17b948a;
2, running the usbd_audio project; It don't control the volume by 52840;
3, Can you help me how to adding the volume control in...
We tried two build options:
1. thread version 1.1 with
# Set OpenThread NCP architecture CONFIG_OPENTHREAD_COPROCESSOR=y CONFIG_OPENTHREAD_COPROCESSOR_RCP=y
CONFIG_OPENTHREAD_THREAD_VERSION_1_1...
Hello
I'm using sdk v17.0.2 and I'm going to program using nrf52840 dongle.
I used nrf52DK because I didn't have nrf52840DK. And I'm going to upload the source code that...
Hi!
I am running Zephyr sample application for direction finding zephyr/samples/bluetooth/direction_finding_connectionless_rx with minor modifications on nRF52833 DK. I...
Hello, I'm developing a BLE application under nRF51422 based on SDK12.2 using softdevice S130. Now, I'm porting the application from Keil to IAR 8.11. There is no compilation...
Hi,
SDK nRF5_SDK_17.0.2
Using :\examples\peripheral\saadc
I want support for multiple peripheral in same project, so i took the saadc example and on top of it add Uart...
Dear Devzone,
We are testing GPS of our products based on nRF9160.
When we test in one car, the GPS signal is lost when the device is put inside this car. This situation...
While testing DFU for OTA ,after entering bootloader mode on my nRF52840 DK, the device doesnt show up either in the device manager or using nRFconnect and Jflash lite . when...
I've 3 FTD nodes (nRF52840 SoC), the network between the nodes and the UDP message transfers are been done successfully.
I want to split and send the messages between...
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
Three software seems to perform OTA DFU: nrfutil command line, nRF connect from desktop, nRF connect from mobile
Do I need all three of them? Are they part of Nordik SDK...
Hi,
I am using an Adafruit nRF52840 Express with a sensor board attached to it. I'm noticing that my sensor IC is reading about 3-6dB higher noise in the 10-50Hz range ...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
Hi Nordic team,
We are busy testing the throughput of the nRF9160. We are having issues installing the NCS at this stage, and was thus provided with a HEX file of the Serial...
