We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
The example app_onoff.c shipped with SDK For Mesh 4.2.0 (unchanged from 4.1.0) have two unused variables in its state struct.
The value_updated variable looks like a left...
Hi
Is the GPIO on the nRF62840 5V tolerant?
I see the VDD supply is capable of 5.5V.
I’m running a 5V Hall effect square wave into the GPIO pin used as an interrupt...
Hi Team,
I would like to send 10 bytes of data in mesh from one device to another device. As i know that we can send data from one device to another device and the packet...
Hello,
I've asked this question around 6 months ago. Now I have to pick up where I left off and I was wondering how much the situation might have changed since.
- Last...
Hi there!
Okay, I've been trying a lot to figure this out, but without any success. I have absolutely no idea what could be the problem whatsoever. The problem is that the...
Hi,
Currently we working on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V4.52
SDK v1.3
CONFIG_MQTT_LIB_TLS ...
I am currently unable to flash any new code or to erase the flash memory of my nRF52840 Preview DK boards.
I am using SES and the OB J-Link, but also tried JLinkExe and...
Hi, I am using the TIFS register of the NRF RADIO to define the interframe spacing timing. (Done with the following line)
During a 1Mbit or 2Mbit connection, the real TIFS...
Thanks in advanced. I update uart pin number to rx:10 and tx:9, then get the error as title described under DEBUG mode. To save power, I use uart but uarte, so I set UART_ENABLED...
Hi,
I'm using the SAADC to sample external voltage to fill in the battery service. I have use APP_TIMER_DEF to create a timer to do it every 30 seconds. Also I have init...
I'm developing a Peripheral with a rather intricate connection process and doing a lot of testing.
I find that if a Central connects, and then the Peripheral tries to send...
Hi,
I have to implement customized services in my project.I think it is better to have seperate files for service inititialization.For that purpose I have seperated service...
This (in SDK v17.0.2):
Experimental: BLE Interactive Command Line Interface Example
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ble_sdk_app_interactive.html...
Hi
I have a coupe of dongles working on a project. While validating the board, i notice a strange behavior: I have the dongles in factory reset (MBR at start, the Bootloader...
