Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I'm using nrf52832 as host and peripheral concurrently, with soft device s132. I know that peer manager can handle both host and peripheral.
I now have a need to remove...
Hi everyone,
We are (still) in the process of evaluating the nrf9160 with the DK.
Our use case is the following one: we want the nrf9160 to send periodic messages in PSM...
Hi, We've developed an IoT platform that runs on Raspberry Pi's that has just been released and we're actively seeking beta testers (see www.omniot.com ). In short the platform...
This is a break from another thread where I was having issues getting the .emproject to show up. Now it is complaining about a missing file...
OK so I went back to the getting...
Hi, I wrote a simple program to communicate with ICM20948 IMU .
The IMU correctly acknowledges its address.
But, when I try to read its WHO_AM_I ID, the program halts...
In previous SDKs (e.g. version 15.0) the following macros were defined in app_util.h
As described in this post these needed to be modified to support more than 15 connections...
I am trying to do the segger development for the 9160 lte ble gateway. When I do the setup info for segger I keep getting a popup saying it can't find the .emproject file...
Hi
I'm working my way through learning how develop BLE Services and Characteristics for an NRF52840. I'm using the 'ble_app_template' example from the SDK (version 15.2...
Hi,
I have the following lines:
NRF_LOG_ERROR ( "This is an ERROR message." );
NRF_LOG_WARNING ( "This is a WARNING message." );
NRF_LOG_DEBUG ( "This is a DEBUG...
I am inquiring about an issue with the SPIM communication. I am reading the who am i sensor of an MPU9250 and it reads 0x71, as it should most of the time but not always....
uVision V5.26.2.0
Error #541: 'NordicSemiconductor::Device:Startup:8.24.1' component is missing (previously found in pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.24...
I have a complete implementation of OTA DFU where iOS app performs a DFU to a nRF based BT Device. Now i am implementing a fix for the situation where:
During DFU, if...
Hi,
I am currently having issues compiling the thingy52-mesh-provisioning demo from github with cmake. The Readme talks about using SES to compile it, which works fine,...
Hello, I have read multiple postings on this problem about how you have to "forget" the MCU on your android to reconnect through Bluetooth. This does not fix the problem at...
Hello,
I am having an issue where the nRF52840 dongle does not properly reset. I'd appreciate it anyone can help.
I was evaluating the DFU options, and erased the IC in...
