Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi, I am in the schematics phase of a new device which may talk via BT to lets say a mobile phone. The communication between the new devices CPU and the nRF52810 shall be...
I'm trying to connect my nRF51 dongle to the DK using the Master Control Panel3.10.0, but I keep getting "no response from master emulator" and failed discovery. I read the...
How do we go about adding servers to the light control example i.e. I would like to control 50 servers via one client. What needs to change in the code besides SERVER_COUNT...
I am modifying the BLE UART example, client and server, in order to have a higher throughput. I have selected that the connection interval is 7.5ms with a total number of...
Now I'm done from send data to the light_client light_service, but I don't know how to send data to another light_server let light_server, I look at the related documents...
I am having issues with the pin_change_int example. I have not changed anything to the code, but it will not load onto my board. In fact, pressing load in this project doesn...
I am trying to implementing eddystone for my nRF52832 and I found two library.
One is with the " /examples/ble_peripheral/experimental_ble_app_eddystone " inside nRF5-sdk...
Hi, I want to NFC connection. so I'm trying to NFC examples.
But, while i was testing NFC_writable_ndef_msg example I have some trouble.
Following the example, I succeeded...
Hello everyone I have a problem where I want to know when a node (server) connects to the gateway (client), how can you control which node, for example, turns light on and...
Hello, I am trying to run the SAADC example code alongside the ble app hrs example. I am able to run both examples individually just fine but when I copy them over to one...
Hello,
I need to implement a simple and minimal serial cable replacement using BLE SoC and external MCU host interfaced by 2-wire UART (without flow control). Is it feasible...
hi
i am beginner to start with BLE.i want create a device i.e bluetooth device and its sevices ,characteristic.which tutorial will most helpful to follow to learn?
Please...
Hi,
My project application is to advertise BLE MAC ID (Company's 6 byte Unique ID) with advertising interval of 30 sec i.e. My BLE will transmit its MAC ID & go to sleep...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
I executed \example\ble_peripheral\ble_app_uart
nrf_log_panic occurs.
I attached...
I'm trying sending and receiving data with spi transaction manager library (nrf_spi_mngr).
The problem is that I cannot receive bytes from SPI device as end_callback doesn...
