Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi guys
I am using SPI example code in SDK11 (./nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi) with nRF51 DK.
It works fine when send first data.
But it get in...
Hello ,I work with the sdk 12, I have a program to contoler the level of battery, it works, except that I recode 3870 mV (with USB) and when I measure the pin VDD I find 2...
Hello,
I am using an Android application to send data to a nRF52 board. The nRF52 board is the peripheral and the Android phone is the central. This is the link establishment...
Hi, I am trying test nRF52840-pdk throughput.
-I loaded softdevice s140_nrf52840_5.0.0-3.alpha_softdevice.hex into nRF52840-pdk using nRFgo
-Then I build (using uVision...
Hi, the datasheet for the nRF24L0+ says that the CRC is the mandatory error detection mechanism in the packet (page 28). Being that CRC can be enabled or disabled via EN_CRC...
Is there a problem logging into Nordic site ?
I have tried resetting my password and it doesn't seem to work. Had posted a question in the this thread earlier
Dear Nordic team and community,
Have you encountered the problem where standard BT4.0/4.1 GAP Peripheral device would be "blocked" from connection (kind of "denial of service...
Just want to confirm I can be i2c master with zephyr rtos for nrf52 pca10040.
In link ( devzone.nordicsemi.com/.../) titled "nRF5x support within the Zephyr Project RTOS...
Hello everybody!
I have one nrf52840 DK and nrf528323 DK. I was flashed and test throughput example. I reach 450kbps. ( transfer 1Mbyte in 18s). Can I enhance this speed...
Hi,
We are interested in nRF52840 and we know that nRF52840 supports both on IEEE 802.15.4(Thread, ZigBee) and IEEE 802.15.1(BLE).
However, does nRF52840 can run BLE...
HI
I'm studying how to control mouse and keyboard via HID with nRF24LU1+ module referring to firmware of nAN-22.
Even though I set Descriptor as appropriate for mouse...
I'm using FDS and define record_chunk.length_words 173.
system waits for fds operation is finished and in the meanwhile, system sleeps using sd_app_wait().
Then, sd_app_evt_wait...
Hello
i am using BLE Relay example with softdevices 132 and sdk version 13.
i make this example simple, no more connection.
just adverting and scanning continuously. here...
Hi all,
I'm using nRF52840 and S140 based on the ble_app_uart example. I get a error code 4 when use sd_ble_gatts_characteristic_add to add a characteristic for another...
Hello,
Help me, please.
I am testing ble_app_uart. Softdevice is S130 and SDK is nRF5_SDK_12.2.0_f012efa.
My development board is Waveshare's NRF51822 Eval Kit.
...
