Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I am using this SDK version 17.1.0 as I am using ESB in this project. So far I have gotten ESB, SPI, and UART communications working. SPI and UART are both using easy DMA...
Running on Fanstel BM15M module (nrf54L15) SDK v3.1.1, I seeing a huge timing error when trying to implement a simple timer function. In the code below, I believe I have followed...
Hello,
Caught this Nordic Skydio presentation by chance this morning and briefly mentioned was the use of a dual core processor mcu. Was this the nrf5340 or some other Nordic...
When evaluating the hardware performance, we tested the WiFi speed of the nrf54lm20 + nrf7002EB2.However, the test result was only 2MB per second.I suspect there might be...
I would like to check if our observation with nPM1300's VBAT node is expected per the IC's design.
As a background, in our application ee use a low-leakage switch to isolate...
Hi,
we have made a pull request on github to introduce the LTI support in CTS client, since one of our new devices have a display and needed a user friendly way of supporting...
Hi every one,
If any body have been succeeded in adding DFU support in Fast pair locator tag on nRF52833-DK, if so can you guide me for it?
I am getting configuration...
Hi! I am using nrf connect sdk 2.6.1 and modem firmware 1.3.7 on a nrf9160. I have an application where i need to try to get a fix on a set interval and also sometimes transmit...
Hello,
I am working with NRF52840 dongle.
I built and downloaded the hid-keyboard example to the dongle. HID keyboard function looks good that a "1" is typed by pressing...
Hello Team,
I am using SDK version 17.0.1 and have implemented OTA. I have also implemented a buttonless DFU without bonding and created a Blinky application. However, when...
Hello,
We are also having trouble installing any SDK into the VS Code Ext Pack, for development on the nRF54L15-DK. Have tried each SDK from 3.0.0 to 3.2.1 without success...
Hello,
I have a functional project to access to an SD Card with NRF54L15DK and the version 2.9.2 SDK and 3.1.0 toolchain.
But I have difficulties to access to the SD card...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Dear all,
i have a problem when i compile a project with Segger v. 8.22a (but i tried also with v.8.26) .
The message is:
Linking 'ne_eere.elf' Linking ' ne_eere .elf...
