Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Currently (as far as i can tell) the firmware for the DECT-NR+ mode is mutually exclusive with the LTE firmware, and you cannot mix the two wireless modes as you have to flash...
We use the device shadow "desired" section to send configuration params to the device. The device processes and accepts the params and then returns them in the "reported"...
HI
Based on the nRF54L15 with SDK 3.0.0 and MCUBOOT for OTA updates, I've discovered there's a firmware image compression algorithm available. However, when compiling with...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
When running the NRF Connect SDK SoftAP sample, connected stations disconnect at **exactly 5 minutes** (300 seconds) into the session, regardless of activity or configuration...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
My SPI slave sensor requires a 32-bit frame length. The CS (Chip Select) signal needs to be switched for each 32-bit frame interval, and it also supports DMA (Direct Memory...
Hi ,
I am using skb501 module and which contains nrf52840.I am using nrf5sdk for development for zigbee coordinator because nrf connect sdk is not supportable in this...
Hello!
We are developing a device based on the nRF5340 and using SDK v2.6.0. The firmware implements a USB composite device (CDC ACM + MIDI + Audio). Everything works perfectly...
I am attempting to interface a tas2110 with an nrf52840. I just became aware of some nrf52 limitations and wanted to get the latest info. My requirements are as follows "The...
as shown in this document:
https://www.bluetooth.com/wp-content/uploads/Files/Specification/HTML/Core-54/out/en/host/attribute-protocol--att-.html and Zephyr's att.h , 0x0d...
When I run the peripheral_hids_mouse sample, I scan/connect on nrf connect and see an instance of the peripheral. then if I clear and scan again in the Discovered devices...
The J-Link itself can’t “see” the external flash — it only talks to the nRF5340’s CPU via SWD. I would like to program initial image of the external flash. 1. On Segger website...
