Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I am beginner with NRF52840. I want to create a task scheduler using multiple tasks with different level of priorities that is low, medium and high. I am using SDK...
Hello,
I got two PCA10056 1.0.0 DKs equipped with an nRF52840 rev. 1 (code AC0). Both do not measure the VCCH voltage correctly (displayed voltage ~2.4V instead of 3.0V...
This forum feels pretty advanced, so if this is the wrong place to ask this question apologies and please let me know where I should be asking it instead.
My goal is to...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0, with updated MDK (see link )
IAR EW ARM...
Hi Everybody,
I need help in writing a little software on NRF52805 which will active the transmitter with parameters:
1) Frequency : 2402Mhz only. (and i will later...
Hi,
I'm using nRF52832 with S140 v7.2.0 base on nRF5_SDK_17.1.0. I use PCA10100 development kit and set VDDH/5 as input and use internal reference (0.6 V) to do the battery...
Hi
I am working on SPI implementation on BL653_dvk board and while SPI_transfer i want to capture the timeout error.
but not able to differentiate which timeout is correct...
Hello,
We are using MDBT42Q-512KV2 module which is based on nrf52832. There is Central and peripheral ( Foot Pedal Switch ) using same module.
We have used crystal from...
I know from the product specification for the nRF52832 chip that the high frequency clk can use a external 32 MHz crystal as source. My question is, is it possible to supply...
Hello!
I am now developing a product with NFC based on nrf52833.
I need to transmit some crucial data between device and phone, such as device settings.
But I have...
Hi all,
I would like to measure time intervals between gpio edges along with Matter.
I tried to use a 100us timer interrupt but seems it will crash the original matter...
Dear Support
I have made the following findings of my evaluation of the NRF5340 with Version 2.1.0 SDK:
-CIS mode has no constant delay at default settings 48-4. According...
Hello Nordic team,
I have looked at the BLE + Zigbee multiprotocol examples from nRF5 SDK and in these examples, I see that there is a file ' multiprotocol_802154_config...
Hello,
are NRF SoCs considered as BLE certified?
What is the default firmware in such case?
I guess no fw changes are allowed so that certification remains valid, right...
If I only wanted to allow one bond at a time, how could I do this?
For example when someone connects for the first time they would pair and bond, by entering the passkey...
