Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I tried a few demos for the nRF5340-DK and most of them work fine. What's unclear to me is where the TX Power is configured or what the default TX Power is in the Zephyr based...
Can you provide an example of how a thread commissioned Matter device can request and retrieve data from the internet?
I understand how a Matter controller can get data...
Hi,
I'm trying to capture and communicate BLE devices on the Desktop/Laptop running Windows and MacOS.
My Application is to capture BLE packets, Connect to particular...
Hi,
I have an application project using nCS with following prj.conf file:
The issue is I am using nrf52833dk and the flash is only 512kb, my build file .bin size...
We have two products which are very much similar and have both an external RTC. So processor (nRF5340) and external RTC are identical. On one product, let's call it WP, everything...
Hi，nordic
I am using ses6.22a, the sdk is 1710 and mesh5.00. When I integrate the serial port case into the mesh sensor case, the serial port can work normally, but it must...
Hello guys, i'm attempting to record the radio_end event, and i tried to enable it with the following code:
However, the second line constantly crashes the chip.
In...
Hi:
I used the following command to install matter OTBR, but the following error occurred when executing this command;(sudo docker run -it --rm --privileged --name otbr...
hi,
I would like to purchase the following nRF-Desktop. It is a wireless BLE keyboard and mouse set.
https://www.nordicsemi.com/Products/Reference-designs/nRF-Desktop...
Hi,
I am using the nrf9160 and attempting to enable MCUBoot and secure boot. Is it correct that you still cannot use any form of TF-M with MCUBoot on the nrf53 or nrf91...
Hi,
I am currently using the NVS library with the nRF9160 and an external SPI-NOR flash device (MX25R6435F). I am getting concerned with the NVS library causing issues,...
Following Getting started with current measurements on the nRF9160 I applied the
to a Thingy:91 (disabled SERIAL, NCS-2.0.0). With that I get about 0,190 mA. That value...
Hi,
I would like to use the NRF52840 dongle (PCA10059) to transfer UART over BLE.
It seems there are some examples available that look promising, but after a day of struggling...
I face problem in k_sem_take() i build a nrf3540 board its successfully running in peripheral uart and some sample programs. while debugging peripheral connectionless rx and...
