hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello,
Using v1.9.1 nrfConnect and the Coordinator example on a nrf52840 -DK. From Nordic docs: I think I may be miss interpreting Zigbee Cluster spec... Below is example...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
I want to set the GPIO of NRF52840 to the high resistance state. How do I set the GPIO of NRF52840 to the high resistance state, please help me,thanks!
Hi！
I'm working on direction finding using nrf connect sdk.
I have already make a tx (nrf52833) and a rx (nrf52833) and i succeed to receive the CTE and the IQ sampling...
I am working on adapting a project that compiles/flashes the code with a makefile that uses nrfjprog in a cmd line to program a blank nrf52480 with the softdevice and application...
Hi all
In nRF52840_PS Pin assignments sheet, some pins Recommended usage is " Standard drive, low frequency I/O only ", does that mean only low frequency (up to 10kHz...
Hi,
I am writing an application that reads data from the I2S interface, adds it to a queue and sends it via BLE (the code I have implemented so far is added at the end of...
Hello,
I am using the 802_15_4 MAC api to configure my device as a coordinator.
After it has been configured as a coordinator I want another device to connect to it...
I am using nRF52805(SDK 17.0.1 & S112) in my application development. Designed GATT Table Having some custom services with read, write & notify properties, And also, there...
I am testing advertising mechanism of nRF52832 device. But the following error occurred.
app: sd_power_system_off() failed, errCode=0x2006
The following is log messages...
It appears that an incorrect value is being used as the reset handler address so that the jump from bootloader to application is to the wrong address.
I am porting a bootloader...
I can not program the NRF52840 with the programmer software on windows 8.1. However when I run a virtual machine in oracle virtual box using windows 10 it works. I would rather...
Hi all
I have two units, one acts as Central and the other one acts as Peripheral.
I erase chip of one of the units, and then always failed to pairing, with a BT_SECURITY_ERR_PIN_OR_KEY_MISSING...
