Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
hello Nordic
sorry to nag but i am waiting for an answer on the thread below for more then a week now, hope you can attend to it or at list inform that you are working...
Hello Devzone,
Working on my Ubuntu 20.04 LTS host, I recently lost ability to flash my nRF9160dk board. The embedded J-Link is detected by its serial number, but an attempt...
Hi, we are working on an application with 300 nodes. each node do 10sec advertsiment and afterwards 10sec scanning pls check the picture below
1) Beacon2 for example advertisies...
Hi,
I have added an external reset switch on my custom board. Maybe a stupid question, but do I need a pull-up resistor? Because in de schematics of the nrf52840 dk I didn...
Hi,
i want to send and receive data via uart1 (connect to a raspberry and send/receive text).
Is there a simple example that shows how to accomplish this?
Im using SDK...
I'm trying to implement a really simple script to sample voltage values from 5 different analog pins on my NRF52832 DK (using Segger at the moment). I found the SAADC example...
While nrfconnect-3.11.0-x86_64.appimage works well, the update to 3.11.1 ends up without Apps.
Ubuntu 18.04
NCS 1.9.1
I found a past case and removed the config and...
Hi,
I am working with NRF52840, I am using segger embedded studio as V5.42a from that I build the example code as ble_app_proximity. I am getting some error as "Output/Debug...
Hello, I am a private developer of wireless gaming mice in Japan. I am thinking of using Nordic's nRF52840 as the MCU, but can this chip be written to only by USB without...
Hi
I added some code to get the PA/LNA driver enabled in the DFU bootloader on my board accordig to this post:
https://devzone.nordicsemi.com/f/nordic-q-a/50687/pa-lna...
Hello! I am quite new to hardware design with these chips, I have been working with NRF24LUP1 for a while, and have custom bin file for it, not a hex file. and I am unable...
Hi,
I am trying to send the data from SAADC on BLE. I follow the example: https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode...
I use PCA10059 demo board,receive BT data by" nrf connect for desktop",yesterday it is ok,but today when I plug it into my PC,it can't be recognized.and no any indicator,...
