Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
I'm using VS 1.7.1 on Windows 10, with the nrf9160dk_nrf9160_ns
Playing around with myFirstApp from the VS Youtube Tutorials, I wanted to redirect output to uart2 and map...
I followed the getting started guide for Ubuntu:
https://docs.zephyrproject.org/latest/getting_started/index.html
I can build Blinky, but when building my project I get...
Hey, I'm starting a new project and I think a very good fit for this would be to have all of my code in an application chip and use a nrf52840 trough USB as a connectivity...
SD140
Our Central Application is scanning to connect to a peripheral's MAC address. When the scanned address matches, we call sd_ble_gap_connect(p_addr,..). But, it is...
Hello! I'm trying to reload CMake in an nRF-Connect-SDK project in the CLion IDE. I've been using this guide: https://blog.jetbrains.com/clion/2021/04/using-nrf52-with-cmake...
Hello,
I am writing the device tree for our custom board, which uses an nRF9160 SiP. This approach to configuring the hardware
is new to me, since my experience is with...
Hello,
We are attempting to track down a rare bug in our code that causes the device to occasionally hard fault.
We have been able to catch it three times, twice where...
Hi,
When I connect nRF52833-DK device to the (Windows 10) system, its JLink UART (COM) Port disappears after some time (in about 4 to 5 minutes.) The following screenshot...
hello Nordic
i work with nrf52840 , .. want to move to ncs 1.8
seems that moving to ncs 1.8 forces me to update to zephyr-sdk-0.13.2 (from 0.12.4)
is it really a must...
Hello,
I have added the line CONFIG_DEBUG_PORT_ACCESS=y in prj.conf file and now the project does not open in Segger Embedded Studio (SES).
I am getting this error,
...
Hi,
I am building my Project in an out-of-tree form and up to this point I solely used Segger Embedded Studio to compile our project. I am using a custom board with an nrf9160...
Hi All!
I am using VS CODE studio as an IDE for nrf9160 FW development. Blinky app compiled and work perfectly. But when I compiled the asset tracker/cloud client it gives...
In my code, the parameter definitions like this :
In my application, I used SAADC in SEGGER to convert my analog sensor input to digital and then i want to sent...
