Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi, i'm developing BLE nrf52832.
Is there any way to display the remaining battery capacity on that window 10 when connecting to Bluetooth like that picture?
The remaining...
Hi,
We are programming our devices (nRF52833) in production using a Segger Flasher Portable PLUS.
We use reset after programming via SFR access.
Our devices will not...
I'm using the at cmd library ( commands like at_cmd_write_with_callback ) to communicate with the modem.
I'm trying to enable the nrf_modem library to enable OTA updates;...
Hello
in order to analyze reboot reson (HW \ SW) I use the following:
in case of kernel crash I usually get coldstack print, in this case I can analyze and understand...
Hi guys,
Based on the examples that I found in Zephyr samples documentation, I created the program where I am able to measure the voltage and temperature, and then send...
I tried running pc-ble-driver-py/advertising.py
my command was " python3 advertising.py NRF52 /dev/ttymxc4" and then I got following error
Traceback (most recent call...
Hello
nrf_drv_twi_rx and nrf_drv_twi_tx are non blocking calls?
in the SDK example, I see a while loop is used in the read call for instance which basically is blocking...
I am attempting to build a project with the command line tools as described in: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_programming.html, but it...
Dear all,
Can I achieve ble peripheral whitelist advertising without peer manager? (Assuming central address is already known)
Following are several places that I've...
I have been using the PPK II for about a month.
I just upgraded my nRFConnect to 3.7.1 and when I run the profiler, the PPK II is no longer visible (the big green window...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi, There. I am preparing to program a Mesh application based on nrf52840. The application supports the recovery from the points of power off.
So, I have a question. It...
Hi,
I'm working with the peripheral_uart example in ncs 1.6.1 and wanted to enable flow control for uart0, but do not see a way to do that.
How do I enable flow control...
Hi, There,
I develop a communication application based on a beaconing example on nRF52850 DK.
I don't know where I do wrongly. It is always stuck in the "bearer_handler_action_enqueue...
