Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi,
I am trying to receive packets from a device with Zigbee custom profile. Through sniffer, I can see that the device joins the network and sends packets on it but I cannot...
Our board doesn't have LFXO, but I want to run DTM. When I try to switch to LFRC by changing sdk_config.h, it doesn't take effect.
chip: nRF52832
SDK: nRF5_SDK_17.0.2...
Hi, we use the Fanstel BT40 design a RS232 & USB carrier board, when we use battery 3.3V to VDD, there is a DC2.8V output from VDDH. VDDH should be power input, why there...
As known in SDK nrf there is a function battery_level_in_percent() used to calculate battery percentage but it is only true for the CR2032 battery. Currently, I am using AAA...
My application uses a SPI LED driver, which I routed on a PCB to the most convenient pins for routing.
I have already tested my firmware on a nRF52833 DK with an Arduino...
Hello, I'm a beginner at developping nrF52832. My problem is completely similar to this one : devzone.nordicsemi.com/.../add-saadc-peripheral-and-others-to-example-project...
I am trying to measure single-phase mains voltage (240v, 50Hz) by stepping down the voltage to 200mv using a voltage divider and read it with the ADC pin of the controller...
Using NB- IOT JIO SIM in india, not connecting asset tracker Work Up to RRC Connected and stuck there. This is custom code very similar to asset tracker example. We are using...
Dear Sir.
Using the mqtt_simple project , I inserted a 1 sec timer.
Within the timer I want to use the publish routine like this
data_publish(&client,MQTT_QOS_1_AT_LEAST_ONCE...
Hello everyone, we are developing a heart hare accessory for the phone and we want to show the battery status directly on the phone. I found it can show up in the Windows...
Hi, I run nRF5 SDK 15.3.0 with SES 4.30c on a PCA10040. Yesterday I upgraded to nRF5 SDK 17.0.2 and SES 5.60. When I connected PCA10040 I got a message that something wanted...
Hi everyone,
I write a firmware to read the values from a 6-axis IMU and some force sensors. I want to sample with a frequency of 100-200Hz, to store the data in a buffer...
Hello,
I have already a Thingy:91 running and sending me data over MQTT using the mqtt_simple Sample.
Now I wantet do change the broker to one with credentials but unfortunately...
