Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi , I have real ECG device with 2 Click and I almost got NRF52840 with PCA10056 development board. I want to put the analog signal from the ECG device to the ADC on the development...
hi support team,
customer is using 5340 1M i2c interface, and we find out that ncs 1.5 still don't have 1M driver, we have to modify the source code，may i ask the when R&D...
Hi,
I am saving temp data along with timestamps in the internal memory and sending it through ble.
if during transfer the queue becomes full (NRF_ERROR_RESOURCES), I am...
Hello all,
I'm developping a firmeware to test the bluetooth inside of our case. So i want to start DTM with a bluetooth command.
The command goes right, but the dtm_init...
We are switching between two modes of ADC sampling in our application:
single shot - Consists of a routine -> Init saadc -> convert a sample of one ADC channel -> uninit...
Hello,
I am trying to implement the workflow "Application as the manifest repository" as described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hi DevZone,
We are trying to move our existing application from SEGGER compilation to a GCC build for CI / CD purposes. However we are seeing a strange bug with uint64_t...
Hi, I use an NRF52840 in my product. The NRF52 is interfaced with an external module in UART. The NRF52840 is always powered by the battery using the different power mode...
Hello All,
Working in lift industry, I recently recovered a BLE project developed by an ex-colleague running on LairdBL651 using with nRF connect SDK 0.3.0 (nrf52810, Segger...
Hello
I am using app_pwm control. When creating PWM, I am using the code as below, can I put float value in period?
I think I can only enter INT value at the period...
I have cloned the BLE code from the periperal_uart example provided in the SDK. However, I am using C++ so I am perform my BLE initialization inside a .cpp file (i.e. main...
Hi,
i'm trying to compile the asset tracker v2 for the nRF9160-DK but i get the following error:
"opening dependency file modules\mcuboot\boot\bootutil\zephyr\CMakeFiles...
Hi all
I have Openthread setup
BorderRouter [ with Raspberry pi and nordic in NCP design].
EFR32 radio board that has been flashed with ot-cli-ftd and made as Leader...
Kindly confirm modem details, BIP ,Refresh command support etc. as mentioned in sheet. -- Kindly let me know whether the question from the operator is clear
Chip nrF52810
SDK - 17.0.2
SD- S112
Mine is a system which sends out beacon continuously (no scanning).
From the spec, I see that the, 2Mbps is the only feature...
