We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, I am using an nRF51822 EK board to develop a custom application and I was wondering about the usage of the SoftDevice. Under what conditions should I use the soft device...
I have recently updated my DFU code to use the source files in SDK 6.1 to be able to OTA upgrade the SoftDevice and Bootloader. I've been able to get the Application to reliably...
Hi,
I am a newbie and would like to build a solution that combines nrf51822 with Arduino. Is this possible.
I find that there are many nrf5001 + Arduino solutions, but...
Hi,
I try to use APP_ERROR_HANDLER(err_code) with a custom error code ( for example 25) in a custom function. Error code reported is correct, but error line and filename...
hello,
Have any example about how to use "CHANNEL_IN_WRONG_STATE" ?
I don't know how to use it. and also don't know when softdevice return this even.
///< Command...
I am having an issue with pin changes triggering interrupts using app_gpiote. I've set up app_gpiote to watch pin 30 and trigger an interrupt on low-to-high or high-to-low...
Folks,
I'd like to use the single UART peripheral in the nRF51822 in interleaved fashion to support two serial "ports", e.g., sets of GPIO pins dedicated to separate serial...
Folks,
In the latest SDK (6.1) for the nRF51822 I see two versions of SPI master code in the Source folder and examples: with and without "5W" appended to the filename...
Hello,
Been posting a few threads lately on my attempt to get the ble_app_hids_keyboard example to work on PCA10003.
I've gotten the files to compile using Eclipse on...
Hello,
i am measuring the current on my nrf51822 board. While sending messages over I2C i have a current about 4.4 mA.
This should be correct? The CPU, 1v2, hfclk and...
Hello,
i use the nRF51 SDK_v6.1.0.0 with s210_nrf51422_3.0.0_softdevice.hex and EM:Blocks as IDE.
i have included the SD210 into the project wizard and created the s210...
Hello,
i am currently trying to integrate a timer properly to my project.
I want to set a pin to high for a duration of 1msec.
I configured the timer like shown below...
Hello,
i am currently working at a project which includes radio transmission based on th hal_nrf library.
I am using parts of an example code, which worked fine for me...
Hello,
my application is using the event scheduler while the softdevice is not. Is it save to call softdevice functions (like sd_ble_gap_scan_stop(), dm_device_delete_all...
