Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
NCS 2.4.1 nRF52840
My project is a battery powered SED based on the coap_client example. It is configured to autojoin using a hard coded pksd. I see on Wireshark that my...
Hello, I want to configure the BMP390 using I2C on my custom board. However, when I try to read the CHIP_ID register, I am unable to get the default value, and the function...
Hi,
I referred to this doc for hardware setup
However, in the programmer in nRF Desktop, I got the following log:
17:37:36.199
Error: Failed with exit code 1...
Hello person in charging,
I would like to know whether there are something information on vulnerabilities in the proprietary mode of nRF51 and nRF52, respectively.
Thanks...
Hello,
After an update to the NRF connect for Desktop the Programmer application can no longer program my nRF52840 dev kit (PCA10056, 3.0.0). Trying to revert the update...
Hi,
In our project, we're using Mcumgr FS to download files from our device.
After tweaking the BLE configuration parameters using the throughput sample ( https://github...
Hi
The datasheet of the nRF9151 is missing the statement in the nRF9161 datasheet:
RF 3GPP compliancy requires 3.3 V.
Is the nRF9151 reaching compatibility down to 3V...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Recently, we started developing our new project using the nRF52832 as our controller.
We are using Segger Embedded Studio (5.42a) as our IDE.
My question is: Are there...
I work for nRF52833 on NCS2.8.0.
I try to set SB_CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT=y for sysbuild.
build error is occured.
Maybe there is not enough RAM for mcuboot...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
