I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
Hi
I am trying to use nrf52811 using nrf52840 DK board.
First, I check simple GPIO example working on my nrf52811 based custom boards
Second, I checked the Bluetooth...
How can I execute a command to commission a device for Thread by using the QR code or pairing code? (without using the pin_code or discriminator) Thanks.
Hi I want to run an epaper with the nRF52832 therefore is SPI needed. Board file was generated from scratch. In the devicetree I added the SPI modul and a epaper modul, which...
Hi,
I am seeing a strange issue with nRF52840 Dongle when I run a custom BLE connection test repeatedly. Below is my configuration:
FW in nRF52840 was programmed using...
Hi,
I'm learing how the i2s streaming works using the example "echo" under "ncs\v2.3.0\zephyr\samples\drivers\i2s\echo". I have a prototype board with nRF5340 and the audio...
When flashing the chip with a build from the samples/bluetooth/hci_uart via west build -b nrf52840dk/nrf52840 samples/bluetooth/hci_uart --pristine and west flash off the...
Hi,
Is it true that you can not disable the nRESET pin in any way? (So that the MCU does not reset after nRESET being pulled low.)
I've gone through the documentation...
Hi Team,
We are using SDK 2.5.2 with MFW 1.3.5
We need to download a secure file from amazon, we first tried to download file from public server connecting to port 80...
Hi DevZone,
My customer found that when using the NRF5340 PDM, there is significant attenuation if the incoming audio signal is a 2kHz signal.
Upon checking the specifications...
Hi DevZone! I am developing a Bluetooth beacon that needs to use extended advertising due to the need of periodic advertising. I am using custom board with nrf52820, nRF Connect...
The following phenomena have been observed in an anechoic chamber:
Success : After the bt_audio_stream_start function is called, the stream_started_cb callback is invoked...
Hello,
We applied for some nrf9151 samples and designed a simple development board with reference to nrf9151 DK. However, there was an issue during testing that the SIM...
Hi, I'm having problems with the firmware update of the Thingy-91. I received it from my professor to use for my final project (it has already been used by previous students...
I am developing a Github CI pipeline to automatically compile, sign, and upload firmware images for a nRF52840 device.
Because I don't have direct control over the machine...
