I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, im trying to implement hardware accelerated symmetric encyption for bluetooth communication between nrf52840dk and a mobile app. Both the
mobile app and nrf52840k will...
My board (nrf52840 sense) has flash memory P25Q16H . When I put everything off, the board consumes 25uA. To save the last bit of current I would like to put the flash memory...
Hi,
I'm trying to remove the bonding (pairing) using the existing function ( delete_bonds() ) in the " ble_app_hids_keyboard " Sample Application from the SDK " nRF5_SDK_17...
Hello
I'm configuring Ping with AT command using API - nrf9160DK, zephyrOS. However, it doesn't go well. API reply "ERROR".
some other AT command goes well, but, Ping...
Hi, I am using the nRF52840 dongle + nRF Connect for Desktop App, and I would like to configure the data rate for packet advertising. Is this possible? Which one is set by...
I would like to use the cURL libary that is included in the nRF Connect SDK (v2.6.1) a nrf/ext/curl
I started with the download sample (nrf/samples/net/download)
I've...
Hello,
I am using matter SDK v2.7.0, when I run command below:
west zap-generate -z ~/Work/matter/light_switch/src/light_switch.zap -m /opt/nordic/ncs/v2.7.0
I get...
Hello, I designed custom board using nRF52832. But dfu is not working on that board. All other code is working fine. I am attaching schematic file of nordic part for reference...
Hi,
To prepare our new device, we are using a nrf5340dk board.
For our application, we need to perform DFU over BT.
Si, i following the tutorial https://academy.nordicsemi...
Hi,
we have been trying to implement modem delta updates to our nrf9160 project using DFU target. We send delta .bin file over LTE to our device, and save it to external...
Hi,
I want nRF91 to download the nrf52840 firmware update image from nrf cloud and then pass it to nRF52 using SMP over UART.
1.How can I use the nrf cloud FOTA UI...
When I program an interrupt, the NRF52840 requires 250uA extra. I read something about the sense interrupt, but I cannot find any working example. How should I implement an...
Hi,
I am working with Thingy53 using the ESB (Enhanced ShockBurst) library. I have my basic app running with multi-point comms and power control. This was done without using...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
