I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
The examples for the Matter Light Bulb app and others contain pm_static_...yml files with sections that look like:
I cannot find "orig_span" in the Partition Manager documentation...
I was asked by Nordic tech support to create a new ticket, because ticket number 357092 had become a long a winding thread.
I need a simple utility I can offer to an end...
I am developing a project using nRF5340 to drive some peripherals. During debugging, I found that no matter how I executed the pull-up/pull-down commands, the p1.00 and p1...
I am using qt C++ to refactor the dfu master station, currently I have a problem, that is, I want to communicate with 52840 simulated com but failed, I initialize, you see...
When I click ACTIONS/Build to build, the executable module(merged.hex) is not created. Now that zephyr/zephyr.elf has been created, the process will finish.
[Environ] nRF...
Hi,
I wanted to characterise the CS accuracy by changing the default parameters in
I get errors when I try to change rtt_type to sounding sequence. I tried both 32 and...
My customer Penguin ID has the following question about HCI USB for the nRF54LM20A. He claims this is only on the old Zephyr stack and not on the new one. Can you please comment...
Hello,
I'm doing some experimentation with nRF54L15DK dev kit.
I connected PPK2 to P6 on the board to measure VDD:nRF current consumed.
The DK is loaded with a release...
I’m working on an nRF5340 project (NCS 2.9.2) with simultaneous multi-image DFU using MCUboot, MCUmgr (SMP over BLE), and external flash (MX25R64, like the DK).
App-core...
Hi
I am moving an application to nRF54L15DK.
SDK is v3.2.2, single core only, no sysbuild.
Whenever I try to debug I get:
-- west flash: using runner nrfutil -- runners...
Hi,
i am developing under NCS 3.2.1.
I would like to if there exist a stand-alone command for creating DFU (nrfutil sub-command or similar) instead of https://github.com...
Hello, in the design reference it explicitly mentions:
“Important note on C9: The grounding of the C9 capacitor MUST be isolated from ALL ground layers except the bottom...
Hello,
I’ve been using SSD1306 128x64 OLED displays with nRF52840 boards for several years without any issues, building with nRF Connect SDK 2.5.x to 3.1.0. Recently, I...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi, we are investigating some devices in field, and have limited logs to work with. From time to time, we see EMM reports with cause 255. According to nRF9160 AT Commands...
