I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi,
I have a question about the System Monitor section of the nPM1300 documentation:
https://docs.nordicsemi.com/bundle/ps_npm1300/page/chapters/core_components/saadc...
Hello,
I'm implementing a device based on the NRF52840 Dongle and the hids keyboard example. The basic functionality work, so that I can send pressed keys to a connected...
Hi,
I am trying to implement a ble module in a fall detection application. I added a ble_service based on the BLE fundamentals course lesson 3, which works just fine alone...
Description:
Hello,
I want to measure the distance between two BLE devices with high accuracy . I have already tried using nRF52840 modules , but the results are not very...
Hello,
I'm trying to detect a UART_ERROR_BREAK on an USB ACM CDC interface of the nRF5340 using NCS2.7.
The returned error code is always 0xffffffa8. How do I clear...
Hi
I have a simple application which is comprised of a notification from peripheral to central , and a write without reponse from Central to peripheral.
In windows every...
Greetings,
We are using a nrf54L15 and trying to use the GRTC Clock output functionality as described in 8.10.4 of the datasheet.
We need the most accurate clock output...
In the next step, I compiled the “Serial LTE Modem” firmware example from the examples folder and flashed it onto the nrf9160DK.
The “Serial LTE Modem” application works...
Hi,
I use the nRF9160dk and I want to use nRF9160's internal flash which has 1MB flash to store a few data. But I cannot find any guideline about using nRF9160's internal...
Good evening, I have recently purchased an nRF52 development kit which I would like to use for my project. Currenty, I would like to provision external devices using this...
Hello, I have a custom board that was designed for me, but based off of the Acconeer XM126. It is very similar with a few minor differences. The person who designed it has...
I'm developing based on the Nordic Academy example here, but I noticed that when transmitting a large amount of data, something is limiting the amount sent by the NRF52832...
Hi,
It seems that CONFIG_IEEE802154_NRF5_UICR_EUI64_ENABLE is not supported on NRF54l15.
Where should be the custom vendor EUI64 value stored?
Only the FICR?
Thanks...
Hello, I recently installed nrf sdk but I have trouble getting through getting started phase. I'm using ubuntu 24.04 and created workspace environment using CLI. Below is...
Hi I'm encountering an error while building Lesson 8, Exercise 1, Step 3 using the nrf7002dk/nrf5340/cpuapp target board. Below is the error message I received:
The same...
