Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi Nordic support,
I'm sort of new to Nordic development..
1. Is it possible to output 32.768 KHz clock on a GPIO of nrf52 device ? In our design we use two crystal oscillators...
Hello,
We are developing an application using nrf52832 and the ncs 1.8.0.
Since our solution is battery operated we have configures application to sleep by default and...
Hi, I try to understand how to use the k_thread_create() to spawn a function (here called spam()) that takes a argument, and then runs with the argument. This code will not...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I am trying on transmit a...
Hi everyone!
I am working on a project where I have to store files inside a FLASH coming from a GATT server , and be able to manage them through FAT in a GATT client . The...
hi professor,
software:nrf connect SDK 1.9.1
hardware:nrf5340
I have merged the peripheral_uart project to peripheral project.When the uart receive data, the asert...
From the introduction video it was stated that the Thingy 53 has a 4-pin JST connector which includes I2C. But there don't seem to be any documentation about this connection...
Hi,
I have just updated to nRF v3.11.1 on my Mac and "Toolchain Manager" is now failing to load, all the other apps seem to run correctly.
I have restarted the app...
Hi,
We are currently filling out the forms for BQB certification and I have some questions. We are using S132 v7.2.0 and NRF52833 for which I have already seen at infocenter...
I follow description of https://github.com/NordicSemiconductor/pc-ble-driver to build pc-ble-driver from source. But it failed to build it.
cmake \ -G Ninja \ .. -- NRF_BLE_DRIVER_VERSION...
I use the vscode to creat a smp_svr sample project ,and how can i easily add fragment to child image(mcuboot)?
as the picture1, the files overlay-bt.conf overlay-FOTA.conf...
Hi Dev Zone !
I would like to do a complete reset to the ESB communication in my application when there is a problem with it for any reason whatsoever. This is what I have...
Hi guys,
I am currently trying to make my uart work with eDMA functionality.
Up to this point I am able to read using polling, and as second method using IRQ with a message...
Hi,
I am working with NRF52840, I need to read some sensor data or potentiometer data and that will transfer in tablet through Bluetooth. So i need a code for SAADC with...
