Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am working with STM32-F401Re with IKO1A2 shield on it as well. I implemented the machine learning core on LSM6DSOX and I get the data of that accelerometer on STM32 F401re...
Hello, I'm in the process of attempting to implement Eddystone EID on the nRF52805.
It's been a bit of a nightmare, so I'm finally taking the bold step to make my first...
Hi,
I am using the nrf52dk_nrf52832 board and adding a peripheral SPI Flash. I had previously gotten the SPI Flash to work but now it does not.
I've hooked it up to the...
Hey guys,
I have recently been using the nrf 52840 dongle to connect to a sensor and gather data from it. So far I have been able to successfully connect to the device...
Hi,
I see that there is Zephyr I2S support in in NCS 1.8.0 (and onward), but I can't locate any reliable documentation for the API.
I have an I2S example (based on https...
HI
I having issue when setting 18 BLE links using s140.
I set the ram size as suggested but still getting error.
<debug> nrf_sdh: State request: 0x00000000 <debug> nrf_sdh...
Hi!
I am using the Serial LTE Modem application from the nRF Connect SDK v.2.0.0
In the source code for this app, every call to:
int util_resolve_host(int cid, const...
Hi,
I'm a student and this is my first project on RF. I'm prototyping my own custom board. I did read in the papers of the quarterwave 2.45 GHz antenna that the PCB should...
Hi,
I am trying to understand either the timing or feature I am missing with respect to LTE, GPS and MQTT. I have read a number of posts and questions on a similar topic...
Hi, I am testing out the UART Peripheral sample on the nRF52840 DK. Since I am communicating with another MCU, I have remapped the RX and TX pins to P0.26 and P0.27 respectively...
The MenuConfig page of SEGGER IDE (ncs1.9.1)：
How should I configure this interface if I want to configure usb DFU and trigger upgrade mode via button: 1.boot_usb_dfu\Use...
I am trying to flash blinky program to nRF52840 Dongle using nRF52840 DK thorugh SWD pins. I successfully implemented that using Segger Embedded Studio by following the steps...
I am working on a project that is being ported from the nRF52840 to the nRF5340 and the once unified radio and app codebase needs to be split to the app CPU and network CPU...
