Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello! I'm trying to use a custom SPM using this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
I closed the previous discussion by mistake: https://devzone.nordicsemi.com/f/nordic-q-a/83067/nrf9160-board-for-qr-code-project?ReplySortBy=CreatedDate&ReplySortOrder=Ascending...
Hi there
The project that I am focusing on was really time-critical, so I'm wondering whether we could disable Link Layer ACKs in nRF Connect SDK (i.e. Zephyr) ? If not...
We have been looking at InsightSIPs AoA Demo kit ( https://www.insightsip.com/products/bluetooth-smart-modules/isp1907 ) and are trying to understand the communication protocol...
Is there a way to access the data that comes into a provisioned node and is relayed on the mesh network, from the application layer in Zephyr?
I have a battery models erver...
Our product under development has tight flash requirements. As such, any optimisation to the build size of the product has a great affect on further development, therefore...
Hi Everyone,
I have seen some posts regarding this topic on the forum but would just like to clarify a few things.
I am currently using an application timer to sample...
This issue exists in SDK 15.2 and earlier.
In nrf_log_frontend_dequeue() when memobj cannot be allocated, the backend flush api is used to free memory. However this memory...
Hi.
The VS code extension Cortex-Debug reports:
' WARNING: Cortex-Debug will deprecate use of GDB version 8. Please upgrade to version 9+ '
The manual installation...
Hello,
Our project based on nRF52840 doesn't work on MacOS after update from SDK 15.0.0 to SDK 17.1.0.
We can't transfer packets over USB because of changes in SDK 17...
Hello,
I'm using the nR5 SDK 17.1.0 and my goal is to implement a TLS client connection between a nRF52840 and an MQTT broker - I have a Wiznet 5500 set up for the TCP stack...
I'm newbie with the nRF environment. I learned how to create a new project in VS Code from SDK samples but now I have two questions:
1 - I want to crate a blank project...
Hi,
My problem is that my relay nodes are in the mesh network, but some of them only connect to the gateway and not to each other. By changing the publish period in the...
Hello,
NCS1.9.1, VSCode, nRF52840,
those uart samples it's not nRF SDK so easy to use.
Is there a simple uart example?
like nRF5_SDK_17.0.2_d674dde\examples\peripheral...
