Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
When I try to build a 'light_switch' project on SEGGER embedded studio for nRF connect SDK 1.9.1 for BMD-330-EVAL board. Running into the following error
arm-none...
Hello Everyone,
I am using NRF52833 in my project and I have my NRF module connected to 2 other microcontrollers on UART peripherals. The details are mentioned as below...
We have first worked with a development kit from Nordic (nRF52840 DK) . We flashed the BLE applications using the nRF Command Line Tools.
https://www.nordicsemi.com/Products...
Hello,
I have to open a new discussion session on the same topic because the current session has been closed.
The topic is as follows: devzone.nordicsemi.com/.../at...
Hi,
We currently have a Gazell project that runs on nRF52832 . We have difficulties changing the project target to the nRF52810 .
From the SDK17.0.2, example: "gzll_ack_payload_device_pca10040...
Hi,
I have a firmware (performing DFU over Bluetooth )that runs well on nRF52833 dev kit and for developing the DFU over BLE. I follow this tutorial
https://devzone.nordicsemi...
Using SDK 17.0.2 I wrote a function to modify advertising interval on the run. The function doesn't return any error but the interval isn't changed. What am I doing wrong...
After nrf_drv_twi_tx() function and nrf_drv_twi_rx() function, m_xfer_done is checked using APP_ERROR_CHECK(m_xfer_done). What is the significance of checking m_xfer_done...
Hi,
I am working on DFU-OTA example on BLE. my doubt here is once the controller copied the image into slot1 bootloader will immediately start to validate whether the image...
I am using the following code to generate and output a n-MHz clock on a GPIO pin. (code is borrowed/copied from another question on this forum)
However, the clock output...
I download the zip file(nrf-command-line-tools-10.15.4_amd64.zip) in the website.
And then I unzip it get the following structure files:
JLink_Linux_V758b_x86_64.deb JLink_Linux_V758b_x86_64...
Hello everyone!
Long story short, we are developing a BLE application based on the Nordic UART peripheral example. The board (STM32 micro + BL652 BLE module w nrf52832 inside...
Hi All,
I have a question about notify data size.
I have a 10byte array, but the length after Notify is sent will be max len = 50byte which I set in characteristic.
...
6 hours ago
Online steve.hou
2 pts.
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am...
