I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I just install the NCS in toolchain manager, but after installation, only one toolchain folder is there,no zephry,no examples,
I'm going to play in VSCode.
what should...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough "RSSI > -45" and initialize...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement my firmware which will consume less current. I have implemented...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. Our custom board has a connection to nRF GPIO...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We need to publish the JSON messages larger than...
Hi, I am developing my own application using the SDK v1.8.0 with Demo direction_finding_connectionless_rx. I notice that in the
cte_recv_cb callback function, the rssi...
Hello,
I am using nRF 52840 DK board and using nRF52SDK17.0.2. I am trying to advertise data in GAP with the name " IG_Last4CharMAC_RFL " for example " IG_4DA8_RFL " but...
hello,
NCS1.9.1, Windows10 X64,nRF5340-DK, nrfx_i2s
in file boards\nrf5340dk_nrf5340_cpuapp.overlay
i've i2s DAC model ,it must use 4 line(MCLK,SCLK,SDIN,LRCK)
but...
I am trying to get this example program https://github.com/ARMmbed/mbedtls/blob/mbedtls-2.11.0/programs/x509/cert_req.c (stripped out all the file handling stuff) to run on...
Hello,
I crated a custom peripheral for my application, I took the code from the Blinky example and i changed the service.
I set the FIRST_CONN_PARAMS_UPDATE_DELAY parameter...
I would like to be able to use 3 different USB descriptors.
1. CDC ACM
2. Mass Storage
3. Composite device with CDC ACM and Mass Storage
These should be selectable...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK. I am using openthread protocol...
