Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
How precise do the trace antenna dimensions have to be? Given that the datasheet for the nRF54L15 only has a reference layout up to and including the matching network, but...
Hi Nordic:
We currently need to provide the RoHS and MSDS test certificates for our product's NRF52820QDAA-R. I checked the certificates on Nordic's official website, but...
While testing, I encountered the following error after flashing the modem firmware and running the DECT example:
<err> nrf_modem: Modem has crashed, reason 0xfff, PC: 0x0...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
I am new to this device, so please bear with me during the inevitable simple misunderstandings! I am scanning for bluetooth devices and getting sensible numbers of devices...
Hi, I have a custom board with an ISP1807 onboard. We'd like to optimize the production process, especially the programming process. We currently use the nrf52840 dk board...
I have a small demo, based on the hello world example, where I have also enabled gpio_keys. I can run this on the nRF52-DK, nRF54-DK but when I come to run it on my custom...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
Hello everyone,
I am using NRF5340-DK for my project and I am trying to combine X509 certificates (using MBEDTLS) with RSA operations (using PSA). This is my current proj...
I am working with the wisblock 4631 from rak, that contains an NRF52840. I am working with the Zephyr infrastructure and uploading code via the Nordic extension for VS Code...
Hello,
We have developed a custom System-on-Module based on the nRF9151 SiP and are ready to begin testing its NTN (Non-Terrestrial Network) capabilities.
Following the...
Thingy91I: Is there a sample project accessing the environmental sensor (BME688) ?
If not, perhaps a project to access a device via I2C by the nrf5340 SIP.
A related question...
I am trying to use the HTTPS_Client example but I am struggling to get it working. It returns 200 unmodified, which makes me think everything is working in terms of the board...
Hi, I’m trying to provision a P‑256 key pair into the KMU at runtime on an nRF54L15 (SDK v2.9.1) but psa_generate_key consistently returns PSA_ERROR_NOT_SUPPORTED, even when...
