I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
According to my understanding of Bluetooth Core Specification 6.0, Volume 6, Part H, "Channel Sounding", it is not a requirement that the Initiator and Reflector...
Hi NRF support team, We are developing a custom board based on the NRF9151 SIP. I am experiencing some issues in provisioning the device to the NRF cloud. On the 9151-DK i...
Hi,
We develop functionalities on native_sim before moving to embedded, therefore I am trying to have nRF9160 modem connected to Zephyr "cellular_modem" sample on linux...
Currently, as a peripheral, I can discover services like GAP and GATT on the host. However, I'm encountering issues when trying to discover the ANCS service. When calling...
Hey All,
Last month a network provider had some internal issues which rapidly started rejecting our devices with several EMM registration issues, however due to not seeing...
Hello All,
We have developed a Zigbee End Node device for which we would like to make a radio test.
we are using nRF connect SDK 2.0.0, please note the reason we use the...
Hello Nordic Team,
I’m currently working with the nRF5340-DK and nRF Connect SDK (v2.6) using VS Code . I’ve been testing OTA firmware update processes using MCUboot and...
Hello
I need help, I have a problem implementing ppi gpiote and spim. The ADC I use is mcp3562 which sends via the irq pin when the data is ready. I need to work in continuous...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello I have an nRF52840 board with a 2 MB external flash I'm using SDK 2.6.2 I'd like to configure the mcuboot_secondary partition to be on the external flash
Here is my...
Hi,
I'm about to develop a custom board with nRF52840 IC. For a first test I need an external antenna. I modified a dongle for a first proof of concept. I removed the antenna...
Windows 11, VSCode, NCS v2.3.0
Hi, I have a well-working application that I would like to build ztests for.
I'm reading about how to do that on the test framework page...
I often see the following warning when requesting a GNSS location: "<wrn> location: PSM is configured, but modem did not enter PSM in 2 minutes. Starting GNSS anyway." - what...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
I have an nRF54l15-PDK dev board (brand new):
I did the following commands with the SDK v3.0.2. Building and Flashing went fine:
to build:
west build -b nrf54l15dk...
