Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi!
I've shipped a whole bunch of PCBs out to customers where pin P0.21 is attached to an IC (which pulls it low by default).
Usually this is fine as the preinstalled...
<install folder>\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.zip\examples\thread\cli\ftd\usb\hex
Need to get confirmation on if I follow the above path and flash the binary...
I have my first custom nRF9160 prototype boards back and they seem to be working pretty well. One question I do have is that I have been unable to find a clear concise description...
Hi all,
I would like to control a stepper motor over BLE. The motor takes STEP(rising edge) inputs for each step. The motor move is based on pre-calculated look up tables...
Как рекламировать процент данных батареи каждые 10 секунд без подключения? Еще мне нужно название устройства. Является ли это возможным? Я использую sdk17.0.2.
After figuring out why MCUBoot wasn't updating my application ( https://devzone.nordicsemi.com/f/nordic-q-a/74145/nrf91-b0-mcuboot-app---mcuboot-not-actually-updating-app...
Hi
I'm trying to run some power profiling with basic BLE apps on nRF5340DK in conjunction with PPKII. Saw several videos in the on-demand webinars section on PPKII and power...
Hi, all.
I'm in trouble in solving a question when i learned NRF52832 recentlly.(SD s132, V5.0, SDK15.0)
I want to read the temperature data from the sensor on-chip and...
Hi,
We widely use this MCU on our products.
Last batch with Rev-D has many issues with burn process.
I'm attaching 2 screenshots along with logs of the problems.
Hello everyone,
I have one or two questions regarding some evaluation measurements on the nrf9160 module. I would like to evaluate the matching network of our nrf9160 antenna...
We use nRF SDK5 17.0.2 with Softdevice S140 on an nRF52840-DK. We have a firmware that we always want to start in DFU mode, then use the abort command to be used to start...
Hi,
I want to read the temperature data from the sensor on-chip and send it to my phone by bluetooth. But as said above, after the connection between my nrf52832 module...
hi all, i'm here to ask few questions on how to get CTE packets. 1. which example can i start off by adding ?
2. can i use dtm to send CTE packets? if do, how can i do that...
