Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am using MeshSDK 4.2.0 and nRF52840.
I have looked into the provisioner example and the provisioner_store function in main.c only seems to store m_nw_state, which only...
Hi all,
I have some issues to print and parse JSON file using cJSON features. My code works without problems in SDK, but when I try the same code in Mesh part, I am not...
Hello, i'm trying to build zephyr\samples\subsys\usb\cdc_acm but i get the following error:
1> zephyr/isr_tables.c does not exist. 1> Combining ‘zephyr/isr_tables.c’ 1>...
With very low data rates and short packets between two nRF52840s which of the following can operate at the lowest power?
1) ble peripheral to ble central uart
2) Enhanced...
Hello Dev
I'm working with MQTT sample on nRF9160 DK device and while that when I called facing some kernel based issue regarding k_sleep() function.
I'm getting this...
Hi,
Thanks for the help. I have run the proximity detection application in nRF52832 nordic thingy. Initially the LED was blinking in the thingy board but when I switched...
Hi,
Though the Thread CLI sample's 'README.rst' lists the following supported optional extensions, it does not specifically describe how to set the specific '.conf' files...
Hi everyone, Lately I have been using a PCA10040 (nRF52-DK) with J-Link OB-SAM3U128-V2-NordicSem V1.00 version. I'm trying to program two boards one with nRF51822_xxAA and...
Hi I am wondering what the best way to go about developing a RPi based system for presence detection with nordic ble devices
I would like to limit the bluetooth signal to...
Hello,
We are looking to do OTA device firmware update by GSM for the nRF52840.
We have a custom board with a nRF52840 and a GSM/LTE-M modem. They are communicating together...
SDK: 14.1.0
CHIP: nRF52840
CONFIG: ZIGBEE&BLE MULTI PROTOCOL
I wants to keep store zigbee pairing data after reset.
I setups like this.
After joining procedure...
From the gnss_extension.rst documentation shown below, it appears as thought the GNSS receiver can retain solution information from previous fixes/tracking in order to speed...
Hello Nordic!
I'm starting to develop my own Zigbee device with the nrf52840DK and I need to send some attributes to my coordinator, initially the door lock status is enough...
I am currently using an external JLINK to program the 9160 module, after adding read protection. Unable to recover using nrfjprog, report the following error:
ERROR: Recover...
