Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi to everyone!
I am working on the SDK 17.0.2 and my project contains nrfx_twim.h functions.
I have a problem to understand the changes that i have to make in the sdk_config...
hi..
I am using nrf52832 and 15.2 version sdk . my laptop 64 bit wndows , there is no software for 64 bit windows , so i installed the 32 bit software
i am getting the...
Hi, I'm just wondering if there could be any chance that the GPIO can be used as ADC? I had my gas sensor output wired to GPIO (P0.03) instead of ADC (AIN0-AIN7) pins. TIA...
Hi,
I tested UART app(nRF Toolbox) by iPhone for scenario: erased bonding info of peripheral but iPhone, then establish connection between iPhone and peripheral.
Here...
I am trying to integrate code on hts221 with an nrf52832. I am using sdk15a for referring the .h and .c of hts221.
NRF_TWI_MNGR_DEF(m_nrf_twi_mngr, MAX_PENDING_TRANSACTIONS...
My programming environment ：nrf52840, nRF5_SDK_15.2.0, armgcc
It shows that MD5 is avaliable in the nRF sdk documents, and I actualy run the hash(SHA1, SHA224, SHA256...
How to set the associated registers of nRF52840 for Ble_LR125Kbit and Ble_LR500Kbit modes. The following configuration did not lead to successful communication. Please help...
Hello Community, I have done some of the programming for nrf52840 for custom ble,interacting two ble devices as master and slave,etc now i want to move on to ble mesh networking...
Hello,
I got a new nRF9160 DK a couple of days ago. I followed the "Getting Started" to get connected to the cloud. But my board is getting connected to the LTE network...
Hello,
My current setup is:
Nrf 52832 custom board (pca10040) SDK 15.3.0 SES 4.52 Soft Device s132 Using a j-link mini EDU debugger
I've tested out the secure bootloader...
Is it possible to change the radio frequency while the radio is running? Our group wants to transmit packets at various frequencies as quickly as possible.
Hi,
I want to send keyboard keys to change tab i.e CTRL+ALT+TAB, how can I send these keys from the Bluetooth HID keyboard to change tabs on my PC?
Thanks
Hello everyone,
I work with the Light_switch mesh example and I would like to send a byte from the client to the server. How can I do this? In the client board, which function...
