Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
My goal: F lash hci_usb in my nRF52840 Dongle, so that i can use Bluez stack in my Linux host and nRF dongle as BT controller.
Build status: Success
Flash : Failed...
Hello,
I am trying to find the electrical and timing specs of the nRF52832 SoC. Where can I find them? In the Product Specification document they are not given.
Thanks...
I'm looking into the best way to split an application implementing a LwM2M stack over 6LoWPAN between the network and application cores of the nrf5340. I fell like the most...
I have an nRF51 based Bluefruit LE Friend device with the Nordic V3 BLE sniffer firmware installed. I am using the associated Nordic BLE interface with Wireshark 3.2.5 (64bit...
Hi everyone.
I know this is gonna be a long story, thank you for your patience...
I have successfully utilized a few examples in the SDK15.3 directory on my PCA10056...
Hello
I have an interesting problem from the ble_app_uart example modified to work with spis.
ble_nus.c code
In the ble_nus.c code (above) I modified to enable notifications...
I have some question about the scan timing, referring to the documentation here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fmultilink_scheduling...
Hello Guys,
I am running an application which is sampling 3 ADC channels at 50 MHz. I am using sample buffers of size 150 and PPI to generate a sample event every 20 microseconds...
Hello,
I found one thread on this issue
https://devzone.nordicsemi.com/f/nordic-q-a/12029/segger-embedded-studio---unplaced_sections-problem
I have added the below linker...
Hi I am new to the SDK and I am working through the examples. I am currently looking at the UART example under examples/peripheral. Iam seeing that both the virtual comm port...
Hi,
I would like to ask, if I just want to "Download program", what components on the schematic diagram are needed?
Download program is OK, so first make sure that...
Hi all,
I've found an alexa gadget example but I can't seem to get it running on my nRF52840-DK. The example I've found was located under repository:
https://github.com...
nrfx_gpiote_irq_handler() which is nearly 150 lines of code. All the GPIOs seems to have same priority at the hardware level, how among different GPIO's Interrupts are processed...
