I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
The example code of beacon was used from the SDK - nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs\ble_app_beacon_pca10028_s130...
Hi experts,
Currently some issues are found in zephyr os, especially the precision of k_timer. Since the nRF51 series uses RTC as the system clock on zephyr os, the round...
I use the scheduler. All my idea is put an event in interrupt handler(timer event, gpiote event and so on) and schedule it to main loop to let app_sched_execute to handle...
Hi All,
We're designing Legacy/Coded Phy scanner based on nrf52811.
The existing softdevice that supports Coded Phy scanner is S140.
Can nrf52811 work with S140 or Nordic...
Hi,
I am struggling with recconecting to Android device. I want the project to work with iOS also.
My nRF de52832 device has got peripheral role in this project. I am...
Hi team,
One of my customer is evaluating nRF52840 running ANT networking, but they may encounter with connection distance issue and wondering if they can combine BT5 long...
Hi,
I just installed the latest nRF Mesh v1.2.1 and found that my nRF52840 DK board unable to connect,
I'm using SDK as shown below:-
nRF SDK for mesh v3.1
nRF SDK...
Hello,
I need to get access to nRF51822 pins in order to test them and connected circuits.
I have access to SWD interface only.
By attempt to read ID register (A2=0...
Hey,
I am running the ble_hid_mouse example on the nRF52832 with SDK15.2 and connected a joystick to replace the buttons commands. now i wanna use the nRF52840 as a slave...
Hello,
I'm trying to create a long range IAS ( Immediate Alert Service ) unsing long range BLE 5.
On the server software I forced the PHY to BLE_GAP_PHY_CODED. I saw in...
The 'Debug Out' on nRF52832 (and 52840?) Dev Kits only works at 3V - so won't work with a 1.8V target.
The question has been asked before, and the obvious answer given ...
hi,...
i am using nrf52382 and nrf52840 ... one is client and server . i am using mesh sdk 3.1 .... i have debugged the example light switch server and client respectively...
Hey
This is sumanth. I have worked on mesh beaconing example and saw the output of continuous scanning advertisement of nearby devices in RTT, I made changes in light_switch_server...
I need to configure 1 device as relay node in order to relay messages from the client node to the server node. To test that the sever is relaying messages i could lower the...
